Liczymy pasujące modele…
"BerninaFeet.stl" is a model for a Bernina Sewing Machine Foot Holder to hold 2 large and 2 small sewing machine feet. "BerninaFeet2.stl" is a model for a Bernina Sewing Machine Foot Holder to hold 5 small sewing machine feet. My wife…
Nähfuss-Halterung für BERNINA und SKADIS. Drei Versionen: - normal - grössere Füsse - normal mit extra Halter für den Fuss 3A. → Siehe Bilder *** Sewingmachine foot holder for BERNINA and SKADIS. Three versions: - normal - bigger feets -…
Storage tray crowbar feet 9mm and 5.5 mm compatible BERNINA Accessory Box. Addition of models for the IKEA panel.
Bobbin holder for bobbin thread jumbo bobbins from BERNINA. An bulge was constructed each side so that the coils snap into place and cannot fall out. In version 2 one bulge was removed, otherwise too much pressure would be exerted on the…
Zweiteiliger Druck! Gemacht für verschiedene Fadenspulen Grössen und speziell für BERNINA Nähmaschinenspulen . Die zwei Teile können einfach mit z. B. Sekundenkleber zusammen geklebt werden. Die beiden oberen Teile sind unterschiedlich…
My wife has a Bernina 800 sewing machine with a lot of different "Presser feet", so I designed this 3d printable hanger so she has them organized and easily accessible. This hanger is for the "9mm" presser feet, which works on many…
Trays and lid for holding Bernina Artista 170 sewing machine bobbins. While I'm sure the bobbins are used in other Bernina models I don't know which. Each tray holds 25 (5 x 5) bobbins. Trays stack together. The lid snaps into notches in…
Bobbins for the Bernina 700 and 800 series are a little odd. They aren't symmetrical -- one side is bigger than another. This is an organizer to pack these fairly densely while keeping them accessible with thread color visible. I designed…
A freestanding/desktop Bernina presser foot cabinet that holds up to 10 small feet & compartments for 2 large feet.. Print with the front side up. Use the attached f3d file if you want to make adjustments. Compatible with the OEM Bernina…
Made a couple modifications to builman's BERNINA bobbin spool tray to enable clean printing with no supports. Print instructions Category: Replacement Parts Summary Made a couple modifications to builman's BERNINA bobbin spool tray to…
I would suggest to print the top and bottom part of the bobbin separately (split parts provided) and glue them afterwards (no support required). Or print the whole bobbin in one piece (support material required). I printed in PLA, 0.2 mm…
A simple reminder tally of the currently installed needle on a Bernina quilting machine. Fusion 360 file included to customize your favorite needle types. Printing Filament: Prusament Lipstick Red Layer Height: 0.20 Perimeters: 2 Infill:…
Designed this holder for cap embroidery. The shield can be clamped between the Cap hoop and Cap clamp. Both get connected with screw and wing nut.
My wife uses a Bernina Artista 200/730 and the tiny screws on the embroidery hoop is very hard to turn. I designed an extension for easy turning of the screw.
One spool for binding and it fits on the knee lifter of a Bernina 570 QE. I printed this spool from PLA. The middle hole looks very big, but when the sewing machine is on a flat table, you need this size of hole for the spool to turn…
Stackable Gridfinity Bobbin holder.
I love my late grandma's Bernina 930 Record sewing machine. It has never failed to power through any project I've thrown at it. But the 40-year-old accessory case has been limping along with duct tape standing in for the two broken…
small modification of the orignal ... a little bit larger ... a little bit "rounder" Category: Fashion
This is known to fit on Bernina 780 and 790 machines. Should fit on all the 7 series machines. Printed in PLA .2mm Layers, 3 permieters and 15% infill. But really almost anything should work.
Little yarn spool to use on an Bernina sewing machine and a storage bin. Also usefull as testprint for accuracy. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .2 Infill: no Filament: eSun PLA…
A simple adapter to allow Bernina Accessory Box Foot Racks to slot into the Ikea Skadis system. The adapter is a simple press-fit and designed so that as many additional Foot Racks can be added by simply snapping them together (Lego…
Someone I love very much was an amazing designer and sewing guru, just wanted to do something to remember them today and ran across the contest. Don't forget to hug your loved ones while you can.
My wife has a Bernina 800 sewing machine with a lot of different "Presser feet", so I designed this 3d printable hanger so she has them organized and easily accessible. This hanger is for the "5.5mm" presser feet, which fit on many…
This is a wall mount that takes Bernina manufactured foot holder racks. 10 racks can be mounted in total. The unit is 300mm tall and 200mm wide.
Nockenstapelgetriebe für Bernina-Nähmaschinen 730, 732, 830, 831, 832, 840, 850 To replace the broken plastik part or use it as negativ for a mold
Note this mount has been superceded by my new version which has a few minor improvements. If you are returning to download because you want one to match one you've made earlier, they still work well. You'll find the newer version HERE…
Nockenstapelgetriebe für Bernina-Nähmaschinen 730, 732, 830, 831, 832, 840, 850 To replace the broken plastik part or use it as negativ for a mold.
Hoops compatible with the Bernette Chicago 7 Embroidery machine. There are two sizes, 100x100 mm and 40x40 mm. I have uploaded the solidworks file if you want to make any modifications. I have also uploaded a template that you can print…
Needed to replace a broken nylon cam gear on an old Bernina Record 730. The model provided on https://www.printables.com/model/298486-nockenstapelgetriebe-fur-bernina-nahmaschinen-730- did not fit well, It appears to be a straight gear…
Put this placeholder on the bobbin winder to make sure the “I thought it was broken since the needle didnt move and it made a weird sound.” doesn't leave your wife's mouth.
In the accessory box of various models of Bernina sewing machines there are thread spool holders that brake quite easily. This is my redesigned model. I printed it with eSun PLA+.
Takes about 5 XL Bernina Spools and is for the Skadis System. Print with some support, and I used a modifier to increase the strength and maybe the lifetime. I printed in simple PLA, Petg and abs etc. should also work.
Bernina at one time made a plastic adaptor to silence the rattle of modern 6mm spools On the thinner spool pin. They are no longer available from dealers, made a simple model to replicate. Original Bernina part was 31906803.
Bobbin holders for the Bernina jumbo bobbins (27.45mm x 9.5mm). Four plates are included: 1x1 (test print) 6X6 6x3 6X1 Please be sure to try the 1x1 test print to ensure that your bobbins fit properly!
The Bernina 1000-series machines have a small accessory box that attaches to the back of the freearm. This box has a small grey clip latch that can break, allowing the box to flip open and lose its contents. This clip is a direct…
I have been building kites for many years, but when packing for my first kitemaking workshop I found that my essential sewing utensils are a bit different from what comes as a pre-made accessory kit for a Bernina 335 - so I made my own…
As I interchange presser feet whilst using my sewing machine, and I wanted a hanging rack that I could stick onto the front of my machine. This single presser foor hanger needs 19mm double sided foam tape to stick onto any flat vertical…
Replacement rear motor mounting clip for Bernina 910 from 1984. P/N 323 868 03 After regular maintenance on a Bernina 910 sewing machine, I discovered a broken rear motor mounting clip. After 20 minutes to model and print a new one we…
Bernina Q20, Q24 (Q Series) - Pin in order to “pin the take up lever” and 2.4mm distance gauges. The maintenance manual often instructs you to pin the take up lever. The hole for the pin is a 3.5mm. This pin design is 3.7mm as my printer…
3x1 Gridfinity block designed to hold 4 Bernina 5.5mm feet.
My mom's overlocker had this piece (which holds the thread bar up), and it broke. This worked as a replacement. I recommend you support it if printing in resin, as the bar channels might otherwise fill up. I drilled a small hole through…
STP model of a Type 01 Foot pedal switch for Bernina sewing machines. Use as basis of design for accessories.
new in openscad and a bit poking around Chambers changes the amound of… chambers, width/depth for bigger footprint, needs some fine tuning in the front lip to prevent feet sliding off (mostly blind hem feet). Massive monster gathering…
The foam part of the Bernina FOAM PAD DISC (“Schaumstoffteller”, part no. 0333277000) gets worn. It is used to “brake” the yarn roll by friction. I replaced it by a TPU part, glued onto the original back plate. Let's see, if this is…
Newer version of the Bernina spool pin adaptor for 6mm cores, this one does not have as much play as it is tapered on the ID. The Bernina 1000 series spool pins are tapered with a spring for storage.
Replacement power knob for my Bernina 1130. It should also fit stitch selector knob on the same side of machine, but I haven't tested it since I can't remove that knob anymore on mine. This is a work in progress to get it to more closely…
How do you fit 43mm discs in a 42mm box… Combining with something else sounds ok but can't really find anything that makes sense… (print is so bad printables doesn't want the photo :p reprinting since… got my magnets reversed anyway)
I have no Idea if this plug is stock as it is different on most machines I have seen.
I needed a replacement footpad for our Bernina 350 series sewing machine. 3D printed on a Prusa MK3S+ with some very old Ninjaflex TPE. Default settings at 0.2mm layer height and 15% infill.
Bernina calibration filter for many vintage machines designed from Bernina discontinued part #0003547100 / 000.354.70.01 for Series ranging 1000-1500 series (Circa 1970's) For calibrating feet 3a&3c with service program 5. Test printed in…
Single square bernina sewing machine foot. Stores upside down. D for the 9mm (C&D), bernina new for the regular. To change for another foot, alter the name and verify if text nr aligns properly (might have to reposition, too lazy to…
Make these simple feet for a sister's Bernina brand sewing machine. I use PETG. Could be made from some flexible filament too.
I had gotten some Mettler and Aman thread spools with the larger 10mm core. The Bernina 1000 series spool pins are tapered, This model will fit on either way and works great with the 10mm core spools.
Deutsch Ersatzteil - Multifunktionsstellknopf für Bernina Nähmaschinen des Modells artista 630 640. Drucken Zum Drucken habe ich PA11 Carbon Fibre verwendet für höchst mögliche Festigkeit. Der Druck mit MK4s erfolgte horizontal mit einer…
Just a regular gridfinity bin, pla and standard profile should do fine. For gridfinity things I do lover the top level to 3 these days and still solid enough.
Replacement rubber wheel for Bernina 807 bobbin thread winding This wheel is smaller in diameter than the original one. The reason for this is: I noticed that the full sized original wheel doesn't fully utilise the "over centre" mechanism…
openscad file is a bit wider slot compared to photo (only got one and low on pla to try but is a bit firm fit)
Just a simple gridfinity bin
I used these parameters on the Rugged Box (Parametric) fusion file. Check original rugged box model for instructions. 30mm screw length 3M I have a Bernina 475QE (Quilters Edition) Sewing Machine and these are the main accessories plus i…
Made for a friend who's restoring an old Bernina industrial sewing machine. Apparently this part is very hard to get ahold of. This is intended to be the form for a sand casting, but I suppose you could use it on its own as a 3D printed…
This is a replacement for the bottom feet for the Bernina 530-2 Record (made in 1963) sewing machine. The original feet fell apart due to age. This simple replacement can be printed in TPU to provide extra cushioning and anti-slip…
Printing Orientation: Vertical for strength Layer Height: .2mm Material: PLA Walls: 3 Infill: Rectilinear 15% Scaling: Scale the model in your slicer to adjust for template thickness (X), table thickness (Y) or printer's maximum build…
rubber roller for driving motor of bernina sewing machine from 80 years ago! to print in TPU95A galet caoutchouc pour moteur d'entrainement de machine a coudre bernina d'il y a 80 ans ! a imprimer en TPU95A Print Settings Printer Brand:…
2x1 gridfinity bin for bernina seamguide with foot 97(D) and piping guide. Includes the screwdriver and place for the screws. Don't have the piping guide so if anybody can confirm it fits... looks about the same. Or you'll have to wait…
I used these parameters on the Rugged Box (Parametric) fusion file. Check original rugged box model for instructions. 30mm screw length. 3M
Mount to the inside of your sew cabinet drawer and place them in. When you go to open the drawer they are right there for you
Replacement power knob for my Bernina 1130. It should also fit stitch selector knob on the same side of machine, but I haven't tested it since I can't remove that knob anymore on mine. This is a work in progress to get it to more closely…
STP model of a Type 01 Foot pedal switch for Bernina sewing machines. Use as basis of design for accessories.
I needed a better way to store my bobbin with the matching thread so I designed this part to slip over the thread post so I can store my bobbin along with the thread. This is the first model I have made! Both the top and bottom post are…
Mount to the inside of your sew cabinet drawer and place them in. When you go to open the drawer they are right there for you
This is my first attempt. Considering what a threaded insert might do to help with this with some permanent Loctite... Maybe V2 An M3x40 may work but I didn't have that kind of time with the hoop to test.
Five pieces are needed to form this box (The font and the walls, Top and Bottom sides, two doors semi-transparent in my case) The side parts fold down at 90° (after heating). Then the top and bottom are fixed with a piece of filament…
The thread spool was too big to fit on the machine so I designed a part that would make it fit. I had to file down the hole a little bit.
rubber roller for driving motor of bernina sewing machine from 80 years ago! to print in TPU95A galet caoutchouc pour moteur d'entrainement de machine a coudre bernina d'il y a 80 ans ! a imprimer en TPU95A Print Settings Printer Brand:…
This insert is designed for flexible TPU to house 18 Bernina type Bobbins in a Plastic Case (135 x 80 x 30mm - I used one from Ali express item No 4001212027744). The insert should slightly grip the Bobbins to keep them in place. I used…
Needs to be printed with supports on print bed. Item on pictures is PETG, 4 perimeters, 20% infill.
Bernina Hand Wheel Replacement. Modern Bernina clip on hand wheel.
Made for the Xl Bobbins on the newer Bernina's, I used PLA. But if I were to remake it I might opt for a PLA Flex and take the size down a bit so the bobbins would fit in snug.
Wanted a thread stand that was portable for my Bernina 1000 series machines. This just slides on to the left spool pin. You'll need a pack of #8 stainless washers and superglue. Tap the rear hole with a M4 screw then get a nylon thumb…
A simple tray to store accessories of a bernina sewing machine.
This gear was made to replace the original bakelite gear made by Bernina in the early 1960s. The new gear can be printed in PLA or other hard wearing plastic. Simply break the old gear off while the new gear is printing. When the new gear…
