Liczymy pasujące modele…
I wanted a carboy drainer that was 3d printable (because why not?). They're stackable, too. References: This model on Amazon was nice https://www.amazon.com/Blue-Carboy-Drainer-Pack-2/dp/B074KL8QD2 but I liked the handle cutout on this…
This is a stand for drying a glass carboy after washing it. Fits both of my 5gal and 6.5gal glass carboys. The neck of the carboy is held in place so that it cannot tip while in the stand. The design is made using two bezier curves,…
Simple perforated cylindrical stand that allows a carboy to be set on it inverted, without the top of the carboy touching the floor/sink. The perforations are intended to allow drying. It is intended to be printed upside down, that way…
I needed a drainer for my carboys as it was dangerous to just lean it against something and that also didn't drain it fully. This allows me to put the carboy upside down with a very stable base with some airflow. Picture is with a ~4.5L…
Remix of Carboy Stopper Clamp from @TheWalrus with additional reinforcement and 10mm stopper height (instead of 5mm). The original is well designed, and this has just a few minor tweaks. This device keeps wet stoppers from slipping out of…
This prints a simple cap for a standard glass carboy, used for when I need to put the carboy into storage, in between brews. It should fit different sized carboys as long as the external diameter of the bottle neck is approx. 54 mm. I…
A Remix version of a Carboy dryer for 1 gallon glass carboy
Straight, simple 19lt / 5 gallons carboy cover. I could not find it so built it.
This is a bung retainer I designed for my carboys, for use when making homemade wine, mead, or anything else that needs to have an airlock installed on a carboy. It is held together with rubber bands to maintain pressure on the bung. The…
I use these plastic carboys from lovebrewing in the UK https://www.lovebrewing.co.uk/23-litre-plastic-carboy/ I've designed this simple 2 piece rack to hold vertically for drying. Stops that annoying puddle forming when they lean. The…
Material PETG or PP
I had some 1 gallon glass carboys sitting in my basement that were getting dust on the inside of the glass. So I made and printed these TPU caps to close them off from spider and dust. Works great. Slides right on and easy to pop off. I…
Brita 5 gallons carboy adapter (damacana) 30% infill with supports Category: Household
This is a simple model of a Pioneer CD-5 Equaliser from the Lonesome Carboy 1 series of car component stereos. Can be used to model holders/mounting kits for lonesome carboy gear, or print as a model if you're so inclined. It'd be nice if…
I was tired of having to dry sanitized bungs prior to pressing them into the carboy and was annoyed by how often they popped right out! This design uses three zip ties to securely hold the bung in place. It also includes a small lip so…
I purchased an electric pump for transferring wine from one container to another (a “Self Priming Anti-Gravity Transfer Pump” - link below). It works well but it can be tedious to hold the pump, move hoses, and watch progress at the same…
Designed for retaining a standard #6 rubber stopper onto a 1-gallon glass carboy. Carboy used: Mouth: ID=28mm, OD=35mm Rib: height=5mm, OD=40mm Two 'inner' parts are threaded and not interchangeable. They surround the lower 'rib' of the…
Picked up some PET carboys (Better Bottle, etc) and discovered that the carboy nozzle base on my Fermtech Double Blast was just a bit smaller than the opening diameter, making cleaning somewhat awkward. This adapter slips on (tightly) and…
This is a guide to keep the racking cane centered to help reduce sediment being transferred when bottling
I purchased an electric pump for transferring wine from one container to another (a “Self Priming Anti-Gravity Transfer Pump” - link below). It works well but it can be tedious to hold the pump, move hoses, and watch progress at the same…
A simple model of a Pioneer GM-4 Component Amplifier from the Lonesome Carboy 1 series. Good for modelling holders, facias, whatever
The modular, versatile, open-source eDNA sampler to maximize detection and minimize complexity The OMNIeDNA sampler is a modular environmental DNA (eDNA) concentration system built around a standard 50 mm cotton swab pad secured within a…
This is a guide to keep the racking cane centered to help reduce sediment being transferred when bottling
This is a simple model of a Pioneer CD-5 Equaliser from the Lonesome Carboy 1 series of car component stereos. Can be used to model holders/mounting kits for lonesome carboy gear, or print as a model if you're so inclined. It'd be nice if…
A simple model of a Pioneer GM-4 Component Amplifier from the Lonesome Carboy 1 series. Good for modelling holders, facias, whatever
Straight, simple 19lt / 5 gallons carboy cover. I could not find it so built it.
A wrench to remove the caps on carboys, 5 gallon water jugs and chlorine containers. Caps are called 70mm screw caps. Print Settings Printer Brand: Printrbot Printer: Simple Black Rafts: No Supports: No Resolution: .2mm layer Infill: 20 -…
