47 modeli
M5Stack Cardputer is interesting piece of hardware. It's quite hard to use when flat on the desk. This angled stand will raise it by 15°. Stick rubber feet to bottom to stop it for sliding. The stand slots into LEGO-compatible holes on…
This is a mechanical reference (dummy) model of the Cardputer , intended for designing custom enclosures, mounts and accessories . The model represents the overall dimensions and main external features of the device and is not a printable…
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. =VISUALIZEM AS IMAGENS= 🔧…
Summary Minimalist hardcase for your M5 Cardputer — designed to protect both the display and keyboard. A small opening on the bottom allows you to easily push the device out when needed. If you’d like to support my work, you can also…
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. =VISUALIZEM AS IMAGENS= 🔧…
Stand for the M5Stack Cardputer-ADV. The pegs are not a friction fit, just for locating. There are pockets for 5x3mm magnets to hold the Cardputer to the stand. Designed to work well with the Cap LoRa-1262 module attached
This is a mechanical reference (dummy) model of the Cardputer , intended for designing custom enclosures, mounts and accessories . The model represents the overall dimensions and main external features of the device and is not a printable…
I made a CC1101 for my Cardputer ADV following Ray J's tutorial on YouTube and decided to design a case for it. Here's the tutorial on how to make the CC1101: Can be printed without supports. I believe the spacers I printed for the device…
⚠ Atenção – Modificação necessária no CC1101 Para utilizar esta case, é obrigatório alterar a posição do conector de antena do CC1101 de horizontal para vertical . Essa mudança é necessária para que o módulo encaixe corretamente no espaço…
I wanted to put my Cardputer up on my HSW, but could not find an appropriate holder for that, so I quickly made one. I like having a lanyard on my cardputer, so that model accommodates that by having holes in the bottom.
"reference model" using marketing materials, a bunch of models off grabcad, hopes, dreams... etc Not perfect, Work in progress, basic reference only. Just release the files M5...
Created a spacer so I could add GPIO headers and a bit more space for larger battery. Short M2 screws needed to hold the spacer on. Make sure there is enough clearance as the front cover screws use the same thread. You can probably…
m2.5x10mm screws switch 4mm https://s.click.aliexpress.com/e/_mqZWCq0
I designed this magnetic mount to bolt to the Rubigrid inside my truck. It prints in 3 pieces. First, the AMPS mount base, which can be installed on an appropriately sized Rubigrid or mounted to a dash with VHB tape. (If mounting to a…
The M5Stack Cardputer pins extender, gives to opportunity to use 8 extended pins [ 5V, GND, G1, G2, CLK, DAT0, CMD, 3.3V ]. Throw this pins you can easily attached CC1101 , NRF and more other modules. For assembling process and additional…
The M5Stack Cardputer Modular Expander is an extension board designed to enhance the capabilities of the M5Stack Cardputer. This expander provides you oportunity to add add additional modules: WIFI external antenna, CC1101, IR Transmitter…
Recommended to print at 5% infill with additional wall support. No supports needed and no screws or other fixings. Clean up the posts and check they are not too tight before placing the Cardputer on too firmly, it should lift off with…
Back plate for M5Stack Cardputer enabling easy modifications (via provided .f3d file) , or change with origial one. Remix it as you like. You maybe will need to increase tolerances becouse I tried to make all holes as tight as possible.…
Warning: In asembly you will NEED hot glue gun for glueing battery module to the plastic frame-thing also be aware and do not overtight screws otherwise screw holes will break off. Antena mod for cardputer providing extended wifi and…
M5Stamp cover to fit in place of factory one if external antena mod is installed. Needs special cable routing (or change in model) to work properly (see photos) Print settings: 0.2mm layer height no supports
I wanted to bring my Cardputer on a plane, and i thought that, for how already it looks like some sort of detonator, the additional battery and the two magnets would have made things even more difficult :P The mesh is all messed up cause…
A case i created, i couldnt find any case to store my cardputer in so i created this one :)
Summary Minimalist hardcase for your M5 Cardputer — designed to protect both the display and keyboard. A small opening on the bottom allows you to easily push the device out when needed. If you’d like to support my work, you can also…
This stand will allow you to neatly mount your M5card computer on your IKEA Skais board.
Eu fiz essa case para o cardputer por hobbie , e esto disponibilizando para quem quiser seguir s mesmos passos , por livre e espontanea vontade assim como um remix por terceiros , estaras livres… Para quem for fazer esteja ciente que…
Recommended to print at 5% infill with additional wall support. No supports needed and no screws or other fixings. Clean up the posts and check they are not too tight before placing the Cardputer on too firmly, it should lift off with…
Allows you to mount an m5stack Cardputer to the Cooler Master Qube 540 PC case
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. Case 3D – CAP RF | Cardputer…
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. =VISUALIZEM AS IMAGENS= 🔧…
A simple remix of hippazoid case but for the Cardputer ADV version and the M5Stack logo. I kept the original parameters for the print: 2 walls, 3 top/bottom layers, 15% gyroid infill and 0.2mm layer height.
Stand for the M5Stack Cardputer-ADV. The pegs are not a friction fit, just for locating. There are pockets for 5x3mm magnets to hold the Cardputer to the stand. Designed to work well with the Cap LoRa-1262 module attached
I made a CC1101 for my Cardputer ADV following Ray J's tutorial on YouTube and decided to design a case for it. Here's the tutorial on how to make the CC1101: Can be printed without supports. I believe the spacers I printed for the device…
⚠ Atenção – Modificação necessária no CC1101 Para utilizar esta case, é obrigatório alterar a posição do conector de antena do CC1101 de horizontal para vertical . Essa mudança é necessária para que o módulo encaixe corretamente no espaço…
⚠ Atenção – Modificação necessária no CC1101 Para utilizar esta case, é obrigatório alterar a posição do conector de antena do CC1101 de horizontal para vertical . Essa mudança é necessária para que o módulo encaixe corretamente no espaço…
I wanted to put my Cardputer up on my HSW, but could not find an appropriate holder for that, so I quickly made one. I like having a lanyard on my cardputer, so that model accommodates that by having holes in the bottom.
"reference model" using marketing materials, a bunch of models off grabcad, hopes, dreams... etc Not perfect, Work in progress, basic reference only. Just release the files M5...
Cardputer ADV Adapter to fit raspberry pi inside More details here: https://www.reddit.com/r/CardPuter/comments/1t4skou/cardputer_zero_diy/
This is a remix of the front panel for Cardputer ADV XL — External 2.8” Display Mod - Free 3D Print Model - MakerWorld With this model you have to remove the header pins and the SD slot from the screen. This model also has the screws for…
A storage case for the Cardputer ADV with the LoRa Cap (with the included stock antenna). External case can be printed using your choice of material-PLA, PETG, ABS, etc. The inserts should ideally be printed in TPU for shock absorption…
This is a simple wrist attachment mount for the M5Stack Cardputer! This mount lets you easily attach and detach the device from your wrist using the devices built-in lego attachment points, and (optionally) four 2x4mm magnets. I think it…
M5Stack Card Computer (Cardputer) Mount compatible with Ikea Skadis Pegboards. Designed in FreeCAD. “split” 3mf file splits model into two pieces if a higher infill percentage is prefered for the back. Otherwise use the STL.
I wanted something to protect my Cardputer when I carry it in my jacket pocket. Buttons, power switch and SD card are all accessible on the back without removing the device from the case bottom as well as the USB-C port on the right (the…
You can keep the whole logo blue/black or choose to color it with the original colors like i did (in your slicer). I printed mine in PLA/High speed PLA using 3 walls, 3 top/bottom layers, 15% gyroid infill and 0.2mm layer height on a…
