24 modeli
+5mm offset for the WPL D12 when you want to run more angle without rubbing on the upper control arm and overfenders . WPL D12 D42 focused 5mm to 12mm aqdapter . May fit other wpl models but not sure if it will work with them .
WPL D12 D42 focused 5mm to 12mm aqdapter . May fit other wpl models but not sure if it will work with them .
Remix of https://www.thingiverse.com/thing:5128517 to allow printing TPU tyres on PLA rims. Also includes a 54mm diameter tyre to keep the same size as the original wheels. Print Settings Printer Brand: ELEGOO Printer: ELEGOO NEPTUNE 2S…
+7mm offset for the WPL D12 when you want to run more angle without rubbing on the upper control arm and overfenders . WPL D12 D42 focused 5mm to 12mm aqdapter . May fit other wpl models but not sure if it will work with them .
Replacement feet for a 43" Insignia TV I acquired. The TV in question uses M4 screws.
Для любителей PCP предлагаю устройство для стравливание воздух из резервуар D42 Корсар (особо актуально у кого редуктор). Идея не моя, увидел на озоне что то подобное, спроектировал и усилил как считаю нужным, испытал, прекрасно работает.…
This is an add to a model from ThingWizard on thingiverse.com. I added the base and fixation screw. It needs : a 3/8' (microphone stand size) ruthex insert for the base a M6 ruthex insert for the fixation, a M6 bolt with square base (see…
Spacer makes lightbar to clamp reliably to oled42c4(i'm pretty sure that it will work with c2 and c3 as well) and prevents it from skewing, 3mm spacer is made to offset light bar up, so lip doesn't goes beyond bezels and overlaps the…
ZEBRA ZD421 Adapter for Rolls Ø 76mm
Using flexible TPU filament and choosing appropriate sizes during customization it fits well and pretty easy to handle and clean. After several attempts with rigid PLA it is a charm in our bathroom. The hexagonal pieces allow a quicker…
This design allows you to get stuff (oscilloscope) off your bench and on your Skadis board where it belongs. This has hex holes to help save some filament. It may also fit other similar models as well. Make sure to check the measurements…
I tried to make a protective casing for the front of the RealSense Depth Camera Module D421. This design is quite preliminary and might require additional refinement to fully tailor it to our needs, but it effectively serves its purpose.…
Its just a simple clip for the famous MD421. It is a failry tight fit, so it shouldnt fall out on its own. It doesnt use the original locking mechanism, as I only found out about it, after I already designed and printed it. You need a M5…
All D and F Series part are compatible
This is a motor mount for the DYS D4215 650 kv motor. It is designed to be used in pairs for a coaxial arrangement, and clamped to a 10mm rod. I am using them on a custom 6s config of the Firefly6. Category: R/C Vehicles
Hold your filters tightly and safely without tools or mods to your equipment. This filter holder for binoculars solidly grips via a sleeve, designed for TPU or other soft material. The solid rings clamp the sleeve between them and hold…
Hold your filters tightly and safely with the option to quickly remove and replace the holder assembly based on your own needs. This filter holder for binoculars solidly grips via a sleeve, designed for TPU or other soft material. A solid…
dishwasher funnel, .stl for edit(SolidWorks).WIP.
Double king for Bongcloud420 (chess variant). Basis diameter: 40,73 mmt The high king, double king or lion king is a fairy chess piece used in Bongcloud420 instead of the king. It can move and capture like a king two times per turn.
Printed replacement for factory tool. Category: Sport & Outdoors
A friend of mine had 2 Sennheiser MD421 Microphones, but only one case. The original inlay was only for a single mic and also not in great shape. I modled this inlay to fit both microphones. There is also a fairly close model of the mic…
Enlarged remix of CYUL’s T48 programmer case. The accessory compartment is widened by 65 mm to accommodate an ADP_D42_EX-A adapter, with additional space behind the programmer for an ADP-017 and cables.…
Its just a simple clip for the famous MD421. It is a failry tight fit, so it shouldnt fall out on its own. It doesnt use the original locking mechanism, as I only found out about it, after I already designed and printed it. You need a M5…
