Liczymy pasujące modele…
Need an extra shelf for IKEA Detolf glass cabinet? That's a solution for you! How to install → check out on my blog Where to buy → My Etsy Store What you need: 4pcs - M3x12 screw ( DIN 912 ) 4pcs - M3 square nut ( DIN 562 , UNI 5596, PN…
Summary Displaying a lot of small items in the shelf but they come with only 4 levels. Tried a few existing designs if found them unsatisfactory and decided to redesign them. There are left and right but you can use just one for all 4…
Here is part 1 of 3 for the huge Diorama which fits for IKEA Detolf Neede Parts Screws 3x 18 (mounting the walls / Intermediate Level) Cylinder Pins M4x16 (mounting walls with floor) enjoy it
A three level figure stand to display four rows (one direct on glass) of figures in a Detolf shelf. Prints best in PETG, especially if you are printing the foot pegs. I included a no peg version that can also be easily modified to add…
This part is used to soozafones Gunpla base to an IKEA Detolf glass display case and create aerial poses for your Gunpla. https://www.thingiverse.com/thing:2702736 Connector is friction fit, and can be combined with several of soonzafones…
We lost one of the 2 hinge pin inserts for IKEA Detolf display cabinets somewhere in the driveway while moving so I modeled a replacement based on the ones we had. V1 is technically more accurate to the original but V2 is slightly smaller…
Clips to make Ikea Dioder LED bars clip nicely into an Ikea Detolf case. Print instructions Print six of the light bar clips to attach the Dioder Bars to the Detolf rails. Print a bunch of the wire clips to keep the Dioder wires tidy.…
I wanted to lower one of the shelves in my Detolf by 3 inches, and I figured this would be an easy way to do it. So far, so good! Let me know if you have any issues. I recommend using 3 spacers per side, aka 6 per shelf. However, I have…
Using this and M3 bolt and screw you can fix this stand which fits 2 pops depending on size. First bolt the “Fixtures” and then just slide the stand into place. Might need a little convincing but it was not the case for me. Print all in…
Allows for placing all your small minis across the side wall of your Detolf display cabinet. The base plate needs to be glued to the legs, and the legs to the ones below them. I have used superglue and it worked fine. Tested with Kingdom…
This project combines a customized NodeMCU Amica housing with a simple wire mold to seamlessly integrate lighting while maintaining a clean and organized appearance. The wire mold, print two to cover one section, provides a…
Maximize your Detolf display case with this shelf extender! Designed to increase the height of your glass shelves by 60 mm, it allows for better organization and more room to showcase your collectibles. Easy to install and 3D printed for…
These are staples to hold led strips on the metal rods of the Ikea Detolf showcases, since with the double-sided tape that the strips come with they fall off over time. I recommend putting 3 in each section, that is, 24 staples per…
These are clips to secure LED aluminum channels inside a Detolf IKEA case. These are designed to be as compact as possible. They press fit onto the ends of the LED channel, then snap onto the wire frame inside the Detolf case. Wiring…
So after moving a Detolf, two feet broke when they got stuck into a transition strip. So I made a new foot. They are not quite exactly the same shape but similar enough and same height.
This thing adds secure clips to your Ikea DETOLF glass display cabinet. The stock product only provides little rubber bumpers to provide minimal sound and vibration protection. A significant bump to the cabinet will have your glass…
Print in PETG for extra strength. It clips onto the vertical rails quite securely on it's own but also contains a hole for a screw for extra stabilisation if required for heavy objects. There are two versions, the triangular one will work…
I had some old IKEA DETOLF display cabinets and when I moved them a few years ago, the plastic pieces that go down the corners to hold the glass sides together just fell apart (I guess because they had been sitting in a window for several…
Made room for the nut outside so you dont need to pause the print :) +Made the space for the silicon thing a bit bigger.
Simple and easy to print door handle for the IKEA Detolf glass cabinet. Needed it because I did not want to touch the glass when I open it.
This remix uses a heat set insert nut to simplify the design and provide easier assembly. Printing: Use PETG, do not use PLA 0.4mm nozzle, 0.2mm height, 25%+ infill, 4+ walls No brim or supports necessary Materials: M3x12mm Socket Head…
