P
Printables
Improved Filametrix Cutter for Bambu Lab Hotend ERCFv2 Voron
Improved filametrix cutter.
Wyniki wyszukiwania: ercfv2
Liczymy pasujące modele…
P
Printables
Guohua A0090 Servo mount for ERCFV2
Supports A0090 as shown in the picture. The A0090 with silver shell does not need to be modified, just use mg90s
P
Printables
Orbiter2.0 Filament Cutter for ERCFV2 with two sensors
Orbiter2.0 SB model adapted for ERCF toolhead sensor, entry sensor & cutter There are only toolhead sensor version and toolhead&entry sensors version, of which the dual sensor version is 1mm higher and refers to the double step design of…
P
Printables
Voron ERCFV2 top mount Enhanced version Does not affect the sealing
Voron ERCFV2 top mount Enhanced version Does not affect the sealing
P
Printables
66mm Voron top hat with ERCFv2 mount - 300mm remix with reinforced 2020 rail mounts
300mm remix with reinforced 2020 rail mounts. Edit 2025-02-03: -added step file for 2020 mounts -added 2020 mount models in 3mf with 0.5 and 1mm larger tolerances for the 2020 extrusion by request. (Untested) -added 2020 mount tolerance…
P
Printables
ERCFv2 Rear Mount for MMB (Longer)
This is a longer rear mount for the BTT MMB for the ERCFv2 it is about 20mm longer so that you can still mount it when using longer gate blocks with pre-gate sensors like these . I exported the mount in question from Fusion (which I am…
P
Printables
ERCFv2 Taller 2020 Mounting feet
not much more to say, I made them taller because I used to have the spool feeds coming from the front under it and I made the mounting screws a little easier to get to
P
Printables
ERCFV2 Support Arm Endcap With BTT MMB V2.0 For ERCT Buffer
Support Arm Endcap With MMB V2.0 For ERCFV2's mod ERCT Buffer Support MMB V1 & V2
P
Printables
v2.4 DOOM ERCFv2 2020 Mount
ERCFv2 Mount for Voron 2.4 DOOMCUBE printers. This mount should also work with standard V2.4 printers. This is installed along the Z extrusions on one side, and mounts 2x 2020 extrusions which mount to the feet of the ERCF. Printed with…
P
Printables
remix ERCFV2_DD_MOD_NEMA17 ercf v2 beta
This mod is currently in beta testing and is still undergoing refinement. Use it at your own discretion. I take no responsibility for any damage caused to your unit during installation or operation.
P
Printables
ClockWork2 Motor Plate for ERCFv2
I accidentally ended up printing a newer X Carriage that replaced the HS inserts with screwholes. While I managed to get two nuts into the holes and managed to insert the left screw I failed misserably inserting the right one. Ther was…
P
Printables
Fysetc ERB Sturdy Bunny / ERCFv2 2020 Electronics Enclosure
This is a small slightly oversized case that mounts on the bottom of the 2020 profile of the Sturdybunny / ERCF v2 below the filament blocks at the back. Features Accurate USB-C & Power Pass through holes. Left and Right passthroughs at…
P
Printables
Bowden PTFE ERCFv2 Buffer Filament Tube Guide Comb
A small easy to print comb that holds the PTFE tubes at the correct height to prevent the tubes applying pressure to the gates. Printed mine in PLA and it works fine, recommend ABS if its within a warm area.
P
Printables
Filametrix Stealth Burner short cutting arm for ERCFv2
Shortened the top to allow the extruder door to open properly. You will need to adjust the cut position to match the divot in the arm since it is shorter. This is a remix from the original arm. credit @sorted - (Filametrix "don't get…
P
Printables
ERCFV2 Linear Axis Selector Motor Support 24mm height motor compatibility
Cut off a bit, and it can fit a 24mm high motor.
P
Printables
ERCFv2 ERCT BTT MMB Box Lid Cutting and tightening
Because the line I made is too short, it cannot fit into the original box. So, I made some cuts on the box and added a screw tightening device. I will need a heat-melting nut and a 3*40 screw for this.