Liczymy pasujące modele…
Designed tpu parts for botgrinder's grinderino. Also designed a camera mount for Yannik's camera system. Added xt60 rear holder. Use the slicer to slice off from the bottom of the holder if you need it shorter.
Finding room for a capacitor in the Grinderino frame, especially when using the HDzero freestyle VTx is a challenge. By flipping the ESC around there is sufficient room behind the camera to mount a capacitor between the standoffs. This…
HDzero Freestyle VTx antenna mount for the Botgrinder Grinderino quad. Specifically designed to accommodate the antenna tube (length and diameter) of the antenna provided with the HDzero Freestyle VTx kit. Plus, it can add a splash of…
Needed somewhere to put the xt60 on my Grinderino..
A holder specifically designed to mount a ViFly Finder Mini buzzer to the rear standoffs of the Botgrinder Grinderino quad frame. And a perfect match with the HDzero antenna mount designed for this frame. There are two versions of the…
Minor revision of Carlos' arm guard design to make it more secure and less likely to separate from the arm in a crash. Similar to the flange around the upper edge of DUNERUNNER's arm socks…
Replacement for the Grinderino camera mounts to accommodate a nano (14mm) fpv camera without any adapters. The mounts also provide a wider range of mounting positions for the camera, especially to move the camera further forward in the…
In addition to providing frame protection this bumper includes a holder for a 2.5Ghz receiver antenna and a tray to hold the receiver with zip tie slots. Plus, it can add a splash of color to the quad - especially if combined with the…
This design was made to not interfere with the airflow from your props unlike some of the other chunkier designs out there that make you loose a lot of power and efficiency from the air bouncing off chunky skids. Make sure to turn off…
Radiomaster RP1 ELRS antenna and an SMA locked antenna mount for Ummagawd Botgrinder Grinderino 3.5" using TPU. YOU MUST USE TPU - The RP1 Antenna and the print bend a little to get it fitting into place. Secure the T antenna last. A…
Three fixed angle mounts (20, 25, and 30 degrees) for the RunCam Thumb Pro HD camera for use with the Botgrinder Grinderino quad frame. Design was done in OnShape using JoyMonkey's mockup of the Thumb Pro camera and inspiration from other…
20 degree Runcam Phoenix mount for Grinderino. Print in TPU
Just a couple of fixed mounts for the grinderino. Print in TPU on its side with supports for best results 20 degrees for fun freestyle. 35 degrees for those that wanna RIP!
I accidentally ordered 2207 motors (TBS Grinder) for my Grinderino 5", so I printed these in PETG and used the same pattern as a drill pattern to elongate the existing motor mount holes. Probably not recommended, as it may weaken the arms…
I was unable to mount my 20x20 Flywoo stack in my Grinderino as the frame uses M3 hardware, and the stack is drilled for M2 hardware. So I created this reducer to size the holes down from M3 to a useable M2.
Camera mount for the Botgrinder Grinerino. Mounts the camera at 25 degrees. Was designed with measurements from the Foxeer T-Rex but should fit other cameras fine, at worst you might just need to drill in/add another hole for the screws.
always dry your TPU filament first and print at 100% infill with full supports
Standoffs to raise DJI 04 air unit (heat sink on top) with room to mount reciever under air unit. Adapter plate to mount AIO on 20#20 mount, tap the M3 mounting holes and use countersunk M2 screws with washer and nut.
Always dry your TPU filament before printing. Print at 100% infill with full supports. Mirror according to your build preference.
always dry TPU filament before printing. print at 100% infill with full supports. mirror according to your build layout.
always dry TPU filament before printing. print at 100% infill with full supports. mirror print for other side.
Camera mount for the Botgrinder Grinerino. Mounts the camera at 25 degrees. Was designed with measurements from the Foxeer T-Rex but should fit other cameras fine, at worst you might just need to drill in/add another hole for the screws.
I took my original O3 camera/UV filter protector design and made a model for my new Grinderino 3.5" build that reduces some of the props in view too. This model also includes arm/motor protectors with built in skids, DJI O3 air unit…
Grinderino 20 degree Camera mount,DJI 04 pro and Immortal T mount, LH and RH SIde covers.
Print for the front of the grinderino to hold an antenna horizontally inside the frame as well as a sled to hold the RX itself. (I just use double-sided tape and pray, seems to do me just fine so far) Specifically designed for the BetaFPV…
Walksnail antenna mount for the grinderino. This fits the stock walksnail antenna (the V1, not the V2 boi, ya know, the one that comes on the whoop boards)
Grinderino 3.5 inch SMA antenna mount with XT-30 connector feedthrough.
Friend needed some longer camera mounts for their pro cam so I quickly whipped these up Its not really 11mm long but its something close to that
For 6mm standoffs. Note: The second holder must be mirrored on the X axis Material: TPU Infill: 100%
This is designed for the Grinderino back bumper, and the antenna faces downward. It is designed to be printed with the bumper facing upwards. It is for the Flywoo atomic UFL LHCP antenna. It helps to keep the antenna from being caught in…
It holds the camera at a 29° angle but since it's parametric CAD you can go into on shape and change that angle and really everything about that design. My camera is the foxeer razor V2 Mini, and if you've had the problem of your camera…
