Liczymy pasujące modele…
I drew up a QR plate for my gorilla pod, because the original one broke. The hole on the bottom has got a diameter of 19mm to fit the screw with a “handle” I had laying around. It should print just fine without supports, but you might…
Simple GorillaPod JOBY tripod mount for GoPro connectors family Category: Camera
This is a modification of Stamos's remix of the Tripod Mobile Phone Clamp. A base plate for GorillaPods was added.
For the JOBY Gorillapod Quick-Release Plate. These are single piece plates designed to be printed bottom down. MODELS: Joby_Cold_Shoe_ Mount.stl - Great for Speedlights (Off Camera Flash), Mic's and Monitors. Joby_Ram_Mount.stl - 17mm…
Joby Gorillapod Mini Quick Release Plate to Cold Shoe Adapter I designed these are two parts to glue together or for you to utilize in your own models. Print Notes: 1-ColdShoe-Mount-TOP.stl - Print with supports under lip of Cold Shoe
This works with a standard 6 mm camera tripod threading. the hole where it goes through is designed so that you could self tap a thread in making it a stronger hold. it is also designed so that you could print it without supports. it wont…
3D printable quick release plate for the Joby GorillaPod 3K triangular style quick release plate. Designed to be used with a 0.6in / 16mm diameter D-Ring screw, approximately 14mm / 0.55in long, such as these . I iterated on these to get…
I wanted something to clip my joby telepod mobile (smartphone) camera tripod to my small backpack with molle for easy & quick access (and because my backpack is really small). Best printed twice in PETG as it needs some flex for the molle…
An extension to mount a 13" IPAD on the Joby Grip Tight Pro tripod mount. To install remove the two visible screws on the mount plate and replace base with printed part. Layer height 0.15mm Infill 15% Perimeters: 3 No Supports
Replacement ball joints for Joby clamp. The original ball joint, crumbled away just by looking at it. Make sure to reuse the screw part from the original ball, cut it into smaller pieces. Reuse the rubber spacer. Test fit it into the hole…
A holder to organize the joby tripod designed for the IKEA Pegboard/Skadis Print Settings Printer Brand: Prusa Printer: i3 MK3 MMU 2 Supports: Yes Filament: Dosen't matter PLA Dosen't matter Notes: Print like showed in the picture, with…
This is a replacement connector for the Joby Beamo LED light. These allow multiple units to be connected to each other or to a stand/mount with the appropriate size threaded post. The hole on this model is sized to accommodate a ¼"-20…
Led Lamp JOBY tripod/gorillapod mount.
I needed a thicker slot for the iphone 5. The slot is 11.7mm and I shim it with tape to make sure the iphone is press fit. This is a remix of Patmik http://www.thingiverse.com/thing:55497 Category: Camera
A simple holder that allows the pod to snap in. I printed with PLA. Designed to mount to the wall with a single tapered head wood screw. Print this model upside-down.
I broke the handle of my Joby tripod, it is a very fragile part and if you forget to unlock it, it will break easily. After trying to glue it back which was unsuccessful I have turned down to 3D printing and came up with a piece that fix…
This is used to hold battery pack for gopro on Joby tripod. Hold clips over joby leg and gets secured into place with a zip tie. Also mount that helps hold Monoprice 5000Mah battery pack in place on battery holder.
Replacement links for Joby Gorillapod Links are printed in PLA and Hat is printed with TPU 95 Category: Camera
Simple cable organizer clip to secure your video/audio/whatever cables running along Jobys gorilla arms.
The cup grabs the ~24.3 mm rubber ball foot: its lip is narrower than the foot, and slotted fingers flex open so the foot snaps past and sits in a spherical seat. The seat is a "teardrop" (sphere + 45 deg cone roof) so it prints with the…
An extension to mount a 13" IPAD on the Joby Grip Tight Pro tripod mount. To install remove the two visible screws on the mount plate and replace base with printed part. Layer height 0.15mm Infill 15% Perimeters: 3 No Supports
3D printable quick release plate for the Joby GorillaPod 3K triangular style quick release plate. Designed to be used with a 0.6in / 16mm diameter D-Ring screw, approximately 14mm / 0.55in long, such as these . I iterated on these to get…
UPDATE: Now more remixable with more filetypes! This will clip into the side channels of your Zune HD. Attach to the gorilla tripod and mount at your desk, in your car, or anywhere else. PETG is a good choice for its flexibility. Are You…
