Liczymy pasujące modele…
Hey Guys, simply put there was too much dust accumulating in my printer so I decided to add a cover to it. While there are already many approaches to this topic on Thingiverse, I wanted to do my own one and of course share it with all of…
You will need 2 M2x15mm screws for the e3d v6 hotend and you must drill to 3mm the old little fan screw holes for pass thru with the m3 screws. wenn you are using the fan duckt you have to lower the fan speed to about 8% and leave it…
Altered the original design to use Conrad part 719734 and to make the cover fit a little bit more snug. Print instructions Category: 3D Printer Parts Summary Altered the original design to use Conrad part 719734 and to make the cover fit…
Adapted the original design by bcoover to fit my Vertex3D printer. The bracket was narrowed a bit to fit nicely around the Vertex and a slot was added so the flat cable can be run through the handle Update: I added a flipped front case,…
As my standard 5 cm fan died and I only have radial fans in stock I decided to remix the design work of Hest and Nestei to fit a radial fan. To install it you will have to cut the Ty-rap that holds down the ribboncable closest to the…
Very simple strain relief clip for Vellemann K8400 Vertex at the lower edge of the housing. Fits strongly at housing and with cable diameter of 5 mm. Category: 3D Printer Accessories
Just a try-out for an alternative cooling (don't know if I need it but it was fun to make). Instructions I used a new ventilator 40 mm but the one provided by Velleman can also be used (if it still works without noice). Need to drill some…
@Bo_Ris kindly supplied me with the original CAD files of his Ikea Lamp Mount. I split his model into single parts and he asked me to post them as remix. This remix didn't take any real effort, all credits go to @Bo_Ris. He's a great…
You need: 1 Slider printed part 1 Holder printed part 1 Nail 4mm x 50 1 bearing LM6UU 1 axle 6mm, 75mm 2 screws M3x10 + washer 3 screws M3X4 to mount the spring 1 screwq M3X8 to tighten the pencil 1 SG90 Mini servo 3 wired 130mm ribbon…
Based upon excellent work by Bo_Ris / Hardbats. You will need the other parts from here: https://www.thingiverse.com/thing:3044377 https://www.thingiverse.com/thing:2177331 Just a remixed version of the revised Fan duct by Hardbats that…
E3D nozzle holder to rest on the edge of the Velleman Vertex K8400 printer frame. I have oversized the holes as they shrink on my printer (Any advice or feedback appreciated)
Clips to allow the Velleman LED kit for the Vertex K8400 printer to be angled towards the print bed. This provides much better illumination of the print bed and makes the lighting kit more effective. Print Settings Printer: Velleman…
As I found out the Ikea Dioder series was discontinued and I still wanted to put LED-strips in my 2nd Vertex K8400 I bought the replacement series "Ledberg" LED-strips. These need a slightly bigger clips than the Dioder series did so I…
This is an addition to the vertex k8400 3D printer installed to the extruder's board centrifugal fan. Even having the additional extruder's fan duct it helps with extra light while printing. Pay attention that this installation might…
Guide for Filament to avoid running of the filament holder (reel) Originally printed in ABS but PLA wil also do. Products must move/turn easy in each other. The two default M5 bolts should be replaced by M5x18 mm Print Settings Printer:…
Updated version after the design of " Tauchpiranha" for the K8400 printer (clicking noise caused by the moving of the X-Y ax after regular use) Needed 8 pieces set screw M5x20 mm (DIN 916) + 8 pieces Nut M5 + 8 pieces Steel bal 5,5 mm + 8…
customised clip on idea from the clip from saschild for double extruder. (sorry couldn't find the URL anymore) One file is for 2x 4 mm teflon and electronic wire/connector and a file for one 4 mm tube, one 4 mm + wiring and the extra wire…
If you use 40mm fan duct ( http://www.thingiverse.com/thing:672780 ) like me, you maybe dont like to have a hole in the bottom of your vertex. Here is a blind cover with Vertex Logo. Category: 3D Printer Accessories
I liked the original fan duct very much at https://www.thingiverse.com/thing:1196270 However to better mount it, I have added screw holes at the top. Now it sits really stable in my printer Category: 3D Printer Parts
The spool holder with a smaller diameter by pmb is a good improvement for the K8400 printer. However in my place, it does not work with my filament spools, as they slip off the holder after view rotations. This clip put onto the end of…
When I changed my print extruder from default K8400 to E3D, I early realized that it was hard to realize dual printings when not both extruders were exactly adjusted on the same height. At this time, I didn't find any good solution for…
