20 modeli
I recently installed the awesome KlackEnder mod on my Ender 3 V2. The stock dock and mount needed to be revised to work with the different size tabs that are on the Micro Swiss NG backplate. The original probe block and retainer are fine.…
Z brace for KevinAkaSam Belt Driven Ender 3/Pro/V2 and CR10 in 2 motors configuration on normal profile. It will also work with any stock Ender 3 style printer. BOM for dual Z on belts mod M5x16mm x 14 pcs M5 T-nuts x 6 pcs 2x M10 acorn…
Simple design that allows for a cable chained to be screwed to the rear left plate for the belted Z mod. KevinAKASam's design can be found at: https://kevinakasam.com/ This is the cable chain I used:…
I took Inspiration from ChadwickTheCrab , and added a mount for the drag chain to the belt clip. Designed to fit the bottom mount of Boubounokefalos' Ender Switchwire Conversion mod. The chain is a generic 10x11 which comes with 3 holes…
Connect a drag chain to the standard carriage plate.
Tolerances from KevinAkaSam klack ender is v0.15 h2.0 on this model. Parameters to fit with Micro Swiss DD. This is a remix of KevinAkaSams Klackender Probe that i modified to fit a specific printhead. All tolerances and instructions can…
The deck pieces are modified to cover the hole where the z motor would have been, as the belted z mod idlers are much smaller.
This is a remix to the Left Z plate, Direct drive version for Kevinakasam's amazing Belt mod. My remix adds two anchor points for the wiring loom from the printhead and from the X stepper. On my machine I added connectors too all the…
This is the kevinakasam's Ender 3 belt Z mod that I remade to fit inside the Anycubic Mega Zero v1/v2. The models uploaded in this project are the SnVD623 variant, but it's compatible with every variant. The only change between my version…
A mount for the sprite extruder cable and a cable chain for the kevinakasam belted Z mod.
Does what the title says and fits perfectly on the back plate if you use Direct Drive with Dual Z Belted
Edit Jan 3 2024: printed, installed, successful. I am using the single motor driven set up and it has fixed the drooping x gantry issues. Very happy with this set up. Make sure you order longer belts if you follow the build instructions…
The original toothed and F623 idlers attach to where the 2040 and 4040 extrusions cross each other on the Ender. Some printers do not have this type of attachment (such as my Biqu B1 SE). This is a modification of the lower idlers so that…
This is a tool to help assist with the building of the belted-Z mod by KevinAkaSam. It's for use with the option for the bottom idlers that makes use of 2 bearings instead of the GT2 pulley and is designed to help press in and adjust the…
X axis motor mount on Neo have different bolt spacing. I redesigned Kevins right mount for use on left side. Original have slots to insert M3 nuts, I opted for thread inserts.
Couldn't find a z brace for the low profile dual motor version so I made my own :) This does limit built height to 235 :( but I rarely print anything that tall. You will also have to remove the 2020 frame cap on the top if you haven't…
This is a plate for KevinAkaSam's Belted Z mod that allow attachment of a filament sensor on the top corner of a printer. To use this, use two M3 heat inserts where the filament sensor sits. Alternatively you can just use a nut and screw…
This is a set of stabilizers for the Geeetech A20M for use during/after conversion to KevinAKASam's Belted Z mod. It is intended that for one of the stabilizers you use the 355MM leadscrew as part of the stabilizer, while the other…
A modified zip tie mount for the Kevinakasam Frankenstein Toolhead V1, redesigned to support larger zip ties.
This is a set of stabilizers for the Geeetech A20M for use during/after conversion to KevinAKASam's Belted Z mod. It is intended that for one of the stabilizers you use the 355MM leadscrew as part of the stabilizer, while the other…
