Liczymy pasujące modele…
I really like the honeycomb motif on this LattePanda 3 Delta case . Alas, my success rate at producing an intact case has been somewhere around 20-30%. The model prints fine, but it's nearly impossible to remove the support plates without…
Lattepanda 3 Delta mount for Engineering fixture plate
This is my remix of the Lattepanda 3 Delta case. I have added more space for the RP SMAs to fit more easily. I have also bought an IPEX 4/SMA conversion and additional high-gain Wi-Fi antennas .
Two parts. Holes for M4 screws. Lattepanda fixed on M3 screws (hot inserts).
Latte Panda Alpha Case Print instructions Unassociated tags: lattepanda alpha Category: 3D Printing
Use this model to mount a LattePanda Delta 3 to the electronics backpack of your Ender 3 NG v1.2 ! The standoffs on the model are tall enough to allow enough room for M.2 SSDs, and the standoffs include cutaways to ensure room for…
A simple LattePanda 3 Delta Titan case holder compatible with the HSW.
10inch mounting panel for a Lattepanda Sigma. You will be able to access the front of the LP Sigma.
Lattepanda Delta (432) case with support for 80mm fan
### Why this mod? If your LattePanda Sigma hits 100°C under load, your fan is likely dying , even if it's not making noise yet. I discovered this when running Tdarr on Manjaro—the CPU hit 100°C instantly without any weird fan noises.…
I was looking for a clean solution to stack different single board computers. I found this existing design for Raspberry Pi's and adjusted it to hold a LattePanda IOTA.
I really like the honeycomb motif on this LattePanda 3 Delta case . Alas, my success rate at producing an intact case has been somewhere around 20-30%. The model prints fine, but it's nearly impossible to remove the support plates without…
This is a complete enclosure kit for the LattePanda Mu on a Lite carrier board. This is a remix of an elegant design . The improvements add the following features: Pockets for the PCIe port alignment pins on the bottom plate, so there's…
Compact case for LattePanda 3 DELTA Before inserting the LattePanda 3 into the case: break out the support-plates out of the plug slots Cover can be fixed with 4 x M3x10 screws LattePanda Board can be fixed with the 4 original screws (4 x…
Hi! I am using a chamsys pc fader wing for light shows and I needed a kind of strong, reliable backup computer which would rund my light-software as master/slavae connected consoles. I got a decent waveshare 11.9 ultrawide screen and…
A simple case for a LattePanda 3 Delta. It provides access to all pin headers on the top side and access to ports and slots on the side. I printed the lid with supports on the base plate to keep the fan ring and the screw holes nice and…
Work in progress Playstation One Style Case for the LattePanda Alpha. More about the LattePanda Alpha: dfrobot.com Todo: Make the buttons/LED work Power On Power Status LED Custom buttons to Arduino Check heat Rework backside Category:…
I installed a TV on the wall using a Vesa mount. The mount had additional holes for larger TVs. This mount uses the holes with the 100mm spacing to mount a LattePanda behind a TV. I used this in our travel trailer to run plex server on…
This model was created for King's Dharma, a multimedia production. It fits a LattePanda with heatsink/fan installed. There are cut outs for HDMI, USB and power. The top case has room for a lithium ion battery too. The case is held…
Remixed this model to fit on a DIN rail support: https://www.thingiverse.com/thing:3604602 This is the DIN rail support used: https://www.euroclamp.it/index.php/prodotti/SDA-detail
Lattepanda Case Print Settings Printer Brand: Anycubic Printer: All-metal Mega Supports: No Category: Electronics
Case made for the Full-Function Evaluation Carrier Board for LattePanda Mu Compute Module It should be a fit case, so any problems just tell me and i will fix it The case include 2 wall/under table mounts in each side The power button…
Lattepanda 3 Delta mount for Engineering fixture plate
This is a simple enclosure for the Lattepanda Mu Board with the Lite Carrier board. It uses 4 M3 screws to place the board in place and the top clicks in place. It has one button extension that fits into the On/Off button for easy access.…
This case is suitable for the Lattepanda MU with the lite carrier board. The inner case was provided by “fastforward” from Discord. He allowed me to use his STL files and to post it here on printables. The outer shell was designed by me.…
