20 modeli
Uzavíratelná krabička se závitem. Doporučené nastavení sliceru: tryska 0.4 mm nastavení tisku 0.10 mm Detail vyhnout se přejíždění perimetrů 100% pozice švu zarovnaný výplň monotónní hustota výplně 20 % vzor výplně Lightning úhel výplně 0…
Malá uzavíratelná krabička. Doporučené nastavení sliceru: tryska 0,6 mm nastavení tisku 0.30mm Quality vyhnout se přejíždění perimetrů 100% pozice švu zarovnaný nebo zezadu výplň zarovnaný přímočarý hustota výplně 15 % úhel výplně 0…
Sunshade for Mybo Ten Zone scope. You only need a rubber band to hold it in place Pare-soleil pour scope Mybo Ten Zone . Vous avez seulement besoin d'un élastique pour le faire tenir en place Print Settings Printer Brand: Alfawise…
I designed this stand for two WD MyBook / Elements Harddrive to keep the temperatures down and prevent me from knocking them over accidentally. Just mount the feet to a 140mm fan using some M4 nuts and bolts. I used zip-ties to attach the…
I couldn't find a shelf or mount for my WD MyBook to mount on the wall or anything and simply made this to fill that need. I printed mine in PLA at 20% infill but can be done with 15% if you would like. Roughly a 2-2 1/2 hr print. Edit: I…
I designed a sun shade for the Mybo Ten Zone scope loosely based on the original model “ Sunshade for Ten Zone compound scope ”. The shade is made to slip on to the scope from the front. Held in place by a detent that engages with the…
My WD MyBook 8TB got pretty hot running 24/7, so I designed this stand with a 92mm 12V fan. Tipp: Solder the fan to a USB connector and it'll run pretty quiet. Print with support and a slow first layer, otherwise you might loose a feet…
Simple Stand sot Mybook for fast printing
The WD Elements fit a bit too lose and tend to fall through the cooler on the fan, so you can print these out.
Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Filament: esun PLA+ Category: Computer
Description: This case is designed to reduce HDD temperatures without active cooling, while also accommodating a Raspberry Pi mount. Required Materials: You'll need the following parts: 4 side screws (from the original black MyBook…
Print with top down, support enabled. To mount the fans a few drops of superglue can be used.
Inspired with a model by Retro Frog I have made a vertical stand for My Book World Edition (Blue Rings) NAS drive.
Under desk mounting brackets for a Western Digital MyBook Duo HDD enclosure. I have not tried it on the MyCloud Duo NAS version but dimensions are the same so should work. There are 2 brackets, back and front. The larger piece is intended…
This is a custom extruder mount for my geared extruder on a Hypercube CoreXY printer My extruder has M4 mounts 64mm apart. I have attempted to make this part as close as possible to the design intent of the original part. Including…
After several years of having an old mybooklive single disk NAS in a drawer, recently I learned that its original firmware can be changed to OpenWrt, which gives a new life to the gadget. Also, the old 3.5" hdd that came with my unit died…
The Mybo Pathfinder allows the mounting of a magnetic arrow-rest, which is secured by the plunger, but since there is only one berger hole the rest couldn't be mounted securely and may be able to pivot. I made use of the two holes which…
The WD Elements fit a bit too lose and tend to fall through the cooler on the fan, so you can print these out.
a calibration robot, my goals: less than 1M of filament under 20min print test for bed adhesion test for overhangs test for inside interlock test for stringiness BE CUTE nice to fidget with contains by daughter name “Amy” enter the tiny…
