23 modeli
This print is based on https://www.prusaprinters.org/prints/30296-einsy-rambo-raspberry-pi-case-for-stock-frame I modified the case so it can fit a Raspberry Pi4 with onboard fan. My fan modell is ZP-0042 New design Design from…
This is a case with a couple different options for a NodeMCU ESP8266MOD v3.2 by ideaspark with onboard .96 inch OLED display. For the small/thin version you will need M2.5x25mm bolts, washers and nuts. This version consists of the BASE,…
available as a clip on or with the magnet. Mine was a nice press fit in, but you can glue it if needed. Added a hole to help pop it out without destructing it! Props to 荣yan for giving me a starting point, but I changed almost every…
After printing, I recommend using M3 screws and heat set nuts to fasten everything together. It should go together much easier than the previous V1 version. There are two versions of the top case. One is designed to fit the better metal…
Vacuum accessory holders to be mounted to the vacuum using 3M Command Strips or double sided tape. Though these should work with any 40mm diameter vacuum accessories, they were designed specifically for the Shark Vertex Pro Powered Lift…
Two-part accessory mount allows the Levoit LVAC-200 attachments to be mounted onboard the appliance itself for quick use, instead of stashed away in a fixed location. I've always found that I don't spend the time to go get the attachments…
This is a fume extractor for working on smd components and take away the fumes from welding. It has a long "nose" that permit to suck the vapours from the spot where you are working. It uses a 140mm high pressure fan (12v or 24v as you…
I've always like Flymo lawnmowers and this is our current one. The weak spot though is the onboard cable clip which is supposed to hold the cable that runs between the grip switches and the motor. Usually after mowing I notice the cable…
A 7" Screen Holder so you can add an on board screen to your Cooler Master Haf XB Case. Tutorial can be found here: Tutorial for built in screen
Files *_v2.* are for a slightly different design: mainly changes the button and it also has 5degree down angle to have more wings in the camera frame. I use 6 skirt outlines for the button and leave it attached. I glued the button to the…
Print one of each file. you will need 4x 1/8"D x 1/4" magnets for the trays and steel for the lids lids are printed with no top or bottom layers and 10-15% grid infill Category: Toys & Games
I really enjoy using onboard side-car mag holders like this from Soggy-Auggy. The place I play has 15min games. And I rarley need more that (3) mags to get me thru the game using pump springers. I can use more storage now that I use a…
This is a anti-vibration pad for the Vevor Onboard Air Compressor . I recommend printing it in TPU at about 50% infill.
This is just a basic tool holder for the Fitnation Flex Bike Express / Ultra. The bike came with a double open end wrench, a hex wrench and a hex wrench screwdriver combo tool. I didn't use these tools when I assembled it for my wife, so…
dont use supports. there's a hole to put one of those body clips on. or just use a tiny wire.
Printed it with PETG for strength. The fit is rather snug, you may want to vary the scaling of one part a bit to loosen the connection a bit. I recommend printing it vertical due to the overhangs in horizontal position
Note: You need to mirror this part before printing! I made a mistake while drawing this in CAD and I don't know how to mirror it myself. Otherwise, it fits fine on a 5QE915682BG. It enables you to use laboratory safety 4mm connectors…
Wanted to carry my longboard and kids bike outside of the Muli basket so I've designed this simple contraption. Works well though! Printed in PETG, 30 - 40% seems plenty strong. For mounting to your Muli you need: - M4 bolt (20 - 25 mm…
available as a clip on or with the magnet. Mine was a nice press fit in, but you can glue it if needed. Added a hole to help pop it out without destructing it! Props to 荣yan for giving me a starting point, but I changed almost every…
I really enjoy using onboard side-car mag holders like this from Soggy-Auggy. The place I play has 15min games. And I rarley need more that (3) mags to get me thru the game using pump springers. I can use more storage now that I use a…
I've always like Flymo lawnmowers and this is our current one. The weak spot though is the onboard cable clip which is supposed to hold the cable that runs between the grip switches and the motor. Usually after mowing I notice the cable…
Check out the full build video on YouTube here: Please read the building instructions before attempting to print this! This project is designed in collaboration with ELEGOO and printed completely on their brand new Centauri Carbon, and…
