Liczymy pasujące modele…
Slides into the original EDC V1 steer tube system. Swap the o-rings from the original tool carrier and slot the multi-tool into the recess. There is a backstop on one side to rest against the tool and keep it snug. I hated the tire lever…
OneUp V3 Dropper Upper Bushing replacement part. Printed with PETG, brim and 0.15 layer height.
Cut a standard tubeless plug tool to ~4.5 cm from the bacon-holder end Drill to the correct diameter if needed Epoxy the metal piece into the 3D-printed plastic part If it rattles in the threads, wrap the threads with Teflon tape Fits the…
OneUp V3 Dropper Upper Bushing replacement part. Printed with PETG, brim and 0.15 layer height.
OneUp Pump holder with integrated Airtag
Got tired of having my wire wrap hang free... Then got tired of having my wire wrap taped to my frame. Made this simple holder to clip onto the right (or left!) side of the QUBD One/TwoUp frame so I can cable tie the wrap down. This…
Updated and added version 1.1, which drops the height of the spacing between the stepper to the endstop by 2mm to fit better. This change also makes it compatible (checked!) with the TwoUp! Doing the 'make my own thing' for the X endstop…
I recently bought a (very nice) Cotic droplink frame, but was missing the OneUp chainguide part. Not to worry though, I have a 3D printer :D --- I based my design on a mock OneUp model found here , but redesigned it from the ground up to…
Cut a standard tubeless plug tool to ~4.5 cm from the bacon-holder end Drill to the correct diameter if needed Epoxy the metal piece into the 3D-printed plastic part If it rattles in the threads, wrap the threads with Teflon tape Fits the…
Однажды я задумался о том, что с установкой OneUP EDC я потерял возможность использовать вещи, предназначенные для установки вместо крышки рулевой колонки. Например, крепления для велокомпьютеров, разные смешные крышечки и так далее.…
Summary Not all forks support the OneUp EDC. Some have ovalized steerer tubes or a minor internal diameter that's just too small for the full storage container. This adds back the storage container with 2mm shaved off the diameter. It…
Sits in an EDC V1 steer tube with a OneUp top cap. Has a recess for an o-ring. Prints upside down with no supports.
The first pump holder I made for OneUp pumps. It's designed to wrap around a ~38mm downtube. Fits perfectly on my Cotic Solaris Max and may fit others as well. Needs a small O-ring for retention. Category: 3D Printing
I preferred this orientation, so added some angles so the zip ties could hold it at the proper angle. Also tweaked the nozzle end to try and direct the air flow more across the print. Hope it works well, the original was a nice design, I…
Designed for an XXL Transition Spire. Printing in PETG or other non-brittle is recommended. This holds the pump with a snap fit and PLA will break. Found this model useful? Buy me some filament!…
I designed this lower chain guide to clip onto your existing OneUp Components bashguard, this chain guide is a sleek and effective addition to your bike. It mounts easily by replacing the bolt retention clip on your OneUp bash guard. I…
it holds your samsung gear sport to navigate with komoot or similar
For securly holding a OneUp Pump on a Last Glen/Coals and using a FidLock bottle. Bottle can be removed without the pump getting in the way. Holder is shaped to fit to the downtube of a Last Glen/Coal d=55mm
The rubber straps on these Oneup pump mounts seem to break a lot. I have 3 of these mounts so I can carry my pump and tools on all my bikes. And I've broken 2 of the originals. Won't be long for the 3rd to go. Printed in Ninjaflex, these…
Ever ride without your tool? Have a desire to have the lightest top cap ever? Have a bike you are selling with the cap but no tool? I have your solution. Requires one O-ring to seal.
An adapter to replace the plug that comes with the OneUp Components EDC Threaded Top Cap . Designed to be used with the Bike - Mountain Bike Fork AirTag Holder (TPU) . Recommended Print Settings TPU 95A .15mm layer height NO supports…
Printed in PETG with 3-4 perimeters, 25-30% infill and supports on build plate only.
Modified Brian Park's tube strap bracket to work with Oneup's EDC strap
Adapter to accommodate Fidlock Bottle holder on Canyon Spectral:ON Model year 2022+ proprietary bottle cage mount. With the option to mount a OneUp Pump or Both a OneUp Pump and Fidlock Bottle holder Base. It will work with the 600ml…
![Simple X-Axis Endstop holder for QUBD OneUp and TwoUp [Updated]](https://media.printables.com/media/prints/12715/images/113160_5115d957-3bc2-481a-83a7-ff4743205239/img_20140810_152829_12715.jpg)
