31 modeli
This is a LED lighting module that is mounted inside the top enclosure of the Peopoly Magneto X 3D printer. All parts were printed in ABS material. Print 4 pieces of the corner bracket. Print 2 pieces of the long straight piece. Print 2…
A simple print that lets you mount your Peopoly Phenom or Phenom Prime bed at an angle, letting excess resin drip off of the surface easier. Can print on FDM or resin. If printing FDM, use 4 perimeters. You might have to scale this up by…
Update: I have added a version where the notch for the cable has it's opening against the printers frame instead of the enclosure top. This should prevent the cables from getting in the way of the enclosure top if you remove it for…
This is an adapter for Peopoly Lancer Extruder, featured on their newest Magneto X printer.
I designed this fan housing to draw air out of the electronics enclosure on the magneto. It requires two 40mm Fans (I used WINSINN DC 40mm Fan 24V 4028 fans), two M4x8 bolts, 4 to 8 M3 bolts long enough to go through your fans. The design…
Version of mounts for Heat inserts and nuts. Mount is designed to not require PTFE tube (There is still about 5mm air gap but I have not had any issues with it) For standard version, use normal duct. For long version, use volcano duct.
A simple PTFE riser to keep the tube from flopping around. Requires 2 m3 screws to bolt it in place. (I stole 2 screws from the bottom electronics plates)
It is finally here! These panels are designed to replace the ones on the electronics section of the Peopoly Magneto X to allow for proper cooling. These panels can be printed directly on the Magneto X. The only non printed parts are the…
Thanks to the great design building an enclosure should be super easy. I have uploaded the step file so you can start creating your base for the ways to be secured.
01.2025 update - after testing 3010 version for a while I was getting heatcreep issues with PETG with higher amount of retractions. After some consideration I decided to go even smaller and make a better focused and enclosed duct with…
This is a model of the Phenom Forge from Peopoly I designed in TinkerCAD.
I took the Rapid Burner toolhead parts by Chirpy2605 and crudely adapted it to fit the Peopoly Lancer hotend. The Lancer (long melt zone) from Peopoly's Magneto X is only $35 with a flow rate up to 60mm3/s but I couldn't find any open…
This extrusion uses the Y axis rail holes to mount. You need a 8mm LED Strip ( 24V) and M3x8 screws. The main body also works as a diffuser. Easy to install. Just slide a 2x1.25 cable down the structure ( where the cables of the screen &…
The simple (Creality) kept twisting with a spool on it. Designed the base mount to have the guide arm slide in, mount to frame with 3 screws. Although I tried to print this in ASA it will need a stronger filament or resin.
This is an alternate spool mount for the Peopoly Magneto X 3d printer. I did not like the stock mount that came with the printer. I thought it was too flimsy and I had some spools fall off while printing. So, I designed this sturdy spool…
A set of adapters that allow the connection of a 2 inch flexible hose: Directly to enclosure (must cut a 2inch hole in the acrylic panel) To the Jetstream part cooling fan in order to create an air loop to and from an external fume…
1:1 scale Peopoly Forge Build Plate. (Oriented properly for upside down and centre origin) Import into supporting slicers (such as PrusaSlicer) to have a visual, front/back oriented build plate under your build area, or whatever.
I wanted a good drip hook for my Phenom Forge. There are a couple available… but they didn't work as well as I wanted… So I took it into my own hands. Enjoy! pictured is the v2… i failed to realized that it would have a smaller inside…
This is an add on heater for the Peopoly Moai. It uses inexpensive parts available through Banggood and Amazon . Total cost including the power adapter is about $45. The power supply needs to be able to supply around 8 Amps of power so…
Here is a better way to mount the touchscreen on your Magneto when you have the enclosure. The doors won't scrap against the edge of the screen, and you can cover the gaping cutout on the front door of the top section. Assembly: Attach…
The standard version of this bracket won't print flat on a Flashforge Creator Pro , and I didn't want to spend hours printing supports to print it in the orientation that would fit. This slices a small amount off the front of the bracket…
If you want to add a little daylight to the inside of your Magneto X, here you go. https://discord.com/channels/1158578009121501267/1261306292199489668 I wired it to he3: [output_pin daylight] pin: PB11 pwm: True cycle_time: 0.01
needed a stable and solid way to keep my vat while i cleaned and filtered the resin. wasn't sold on any that currently populate the market. so I mades my own. works with this lab stand from vevor . definitely others. which uses M6x1…
Peopoly Magneto X TPU Damper to be able to mount long stepper like the Nema 17 LDO-42STH48-2504AH.
Magneto X Raspberry Pi4 + ToqueCAN Mount Upgrade mount for installing a Raspberry Pi 4 and ToqueCAN system on the Magneto X. The Raspberry Pi plate is designed for the Raspberry Pi4 & ToqueCAN to be assemble outside of the machine and…
IMPORTANT!!! THIS GAUGE BRACKET IS DESIGNED TO BE USED AFTER YOU HAVE DONE THE INITIAL LEVELLING PROCESS FOLLOWING THE GUIDE IN THE BUILD MANUAL. IT IS NOT DESIGNED TO SET INITIAL LEVEL HEIGHT OF THE VAT BUT RATHER TO ENSURE ALL SIDES OF…
I designed a guide cable chain for my Peopoly Magneto X because I couldn't use the original feeder due to space constraints, and a top-feeder using only PTFE tubing didn't work. However, the cable chain and its mount are designed so that…
This is a set of files for adding interior LED lights to your MOAI printer. It includes 4 corner lights and a center light that operates only when the door is opened. The corner lights turn on independent of the printer or door. I mounted…
If, like me, you have printed the resin vat covers by Helmi74 ( https://www.thingiverse.com/thing:2415007 ) to cover your resin vats during storage then this is a simple seal that can be printed in a flexible filament such as Fillamentum…
I designed the riser and electronic covers and equipped them with magnets, allowing for quick removal. You will need the following magnets: 50x 10mmx5mmx2mm You will also need: 3x M3x20mm brass standoffs Print the Middle Riser 10x
Remix of the fan duct for 2x40mm fans as I wanted to use 5015s to draw air from the bottom and keep the noise down a bit. Can be mounted with bolts thorugh the 2 holes or easier with double sided tape
