Liczymy pasujące modele…
Printed the top part without bottom or top layers to create holes for heat dissipation. Warning! Uses heat inserts to screw top in. Parts needed: 4x m3 screws 4x m3 heat inserts
Customisable Gridfinity boxes for storing PCBs or perfboard. I've included some common sizes for perfboard (the dimension in the filenames is the length of the board), but with openscad you can customise to the exact sizes of your PCBs.…
A simple component you can use to represent a 50mm x70mm perf board, for use when designing cases etc. Not suitable for printing. The STEP file can be uploaded then imported into Fusion 360 for use in your projects.
A small enclosure for a Wemos D1 Mini mounted on a 40 mm x 60 mm perf board. There are two screw holes to secure the board and a cabling egress on one side for screw terminals. I created the design in Fusion 360 and have included the file…
Base for 70x30 mm perfboard with Lolin D1 Mini. USB-C charger port in the other end and small hole for cable in the other. Cover fits on top of base snugly, there is just 0.1 mm clearance. Perfboard can be screw-mounted to base part from…
I needed a simple perfboard holder and a method of holding the electronic components in place while I soldered them, so designed this. I printed mine in PETG with standard 0.2mm quality settings and with variable adaptive layer height set…
reference for 16* 10 cm perfboard Category: Electronics
Mount for a perfboard (length 60, width 40 mm, height 1.6 mm).
An easy variant to mount my perfboard, breadboard or stripboard - can be screwed to the wall - plugs into place Breadboard ordered from amazon “azdelivery" in Germany under the term “Lochrasterplatte oder Lochrasterplatine” Three sizes…
Держатель штангенциркуля для перфопанели Ссылка на Перфопанель
There is some clearance under the board for wires to connect components. I think it's best to print it with PLA. Supports are not required. Good adhesion to the build plate is needed. Remember that you can always add some glue, but this…
Paint holders for Vallejo/Tamiya bottles. Version for perfboard with 10x10 holes and 36mm spacing and IKEA Skadis (check note below!). Printed from an orange PETG. IMPORTANT! I added skadis type mount based only on tech drawings i found…
Держатель отверток для перфопанели Ссылка на Перфопанель Ссылка на Отвертки
Improved upon Heartman's design by adding the ability to add label and cutout panel to the back of the box, for power input, audio in or power button. Of course you can customize this design for bigger box just like Heartman's When…
Universal Crossover Perfboard, Multiple Sizes A universal, 3D printable perfboard-style mounting plate designed specifically for passive speaker crossovers. These boards make it easy to lay out inductors, capacitors, resistors, and wiring…
A bin that holds any development board that has bottom pin headers. Uses a 8x12cm perforated board because I don't trust my printer enough to properly print the generic devboard holder made by thessel . You might need to slightly grind…
This STEP file allows you to fully customize your PCB perfboard enclosure's dimensions as well as adjust the mounting holes for the perfboard. Something I needed and wanted to share.
This print requires a ½" diameter x 1/8" thick disk magnet (12mm diameter x 3mm thick). Assembly and Use There are two halves to the print, with a hollow to hold the magnet. Simple place the magnet in the hollow, and hold the two halves…
I built a small cleaning bucket for perfboard instead of a silicone or brass brush since Eddy-NG needs a perfectly clean nozzle. It works 99% of the time and works much better than a silicone or brass brush — at least for me. You need a…
Hook for perfboard (EUROSLOT)
A simple, practical 3D-printed enclosure designed to hold a perfboard for DIY electronics projects. The casing features a protective housing and a removable lid, providing convenient access to the electronics inside while keeping the…
A case I printed out for my perfboard USBasp AVR programmer. I prited it in PLA with a 0.35mm nozzle, 0.30mm layer height and a honeycomb infill of 0,15.
A simple mount for standard 60x40mm perfboard with M2, 56x36mm mounting hole spacing. The model has 4mm of clearance to the underside of the perfboard. It will accept 4-6mm long M2 screws. The mounting holes are about 3in apart and…
This 3D printable case is designed to house an ESP32-S3 DevKitC-1 mounted on a perfboard. It includes opening for the USB-C port, allowing easy access for programming and power without removing the board. An additional opening is provided…
I built a small cleaning bucket for perfboard instead of a silicone or brass brush since Eddy-NG needs a perfectly clean nozzle. It works 99% of the time and works much better than a silicone or brass brush — at least for me. You need a…
