Liczymy pasujące modele…
I wanted a stand for my Gamecube controllers which matched some of the ones I'd printed / designed for 8BitDo controllers, so designed this. I took inspiration from the remixes and attempted to use some of the sizings, but after many…
This holder for the Prusa Mini power adapter/supply, uses very little material and takes short time to print. It can hold all powersupplys with 35x71 mm.
Double PowerA Nintendo Switch controller stand
Remix of the Justin_Itz's original model to be used with the PowerA Charging Stand, which has a different inner and outer profile and the location for the charging pads on the battery pack is off center. The fit from the original model…
Replacement thumbstick for PowerA Switch Controller
OnShape Link No supports required, print with the bottom of the holster on the bed. Only one prototype needed a (small!) raft. Final version printed with no raft in PETG but PLA/PLA+ would probably be just fine. If the OLight is loose,…
this is a modified version of the power bracket that allows sliding it in and out
A simple wall bracket for a PowerA WC001 Nintendo Switch controller. I mounted it to the wall with two command poster strips. Double sided tape would probably work too.
A alternative Powerbank holder for the quest 2 default strap for longer gaming time and better weight distribution on the head :) Just print it upside like in the screenshot with a small support on the two clips. You can easely clip the…
Chick waterer made for the powerade zero triple thread bottle. Fills up about halfway in the bowl. There is also an anti drown model that should work good for quail chicks. But there are three sizes to fit any need! I made a holder with a…
Very straight forward print 0.4mm nozzle 0.2 layer height with supports. Compatible with this Joycon Charger: https://www.amazon.com/PowerA-Nintendo-Switch-Joy-Charging-Dock/dp/B01MR6JD1M
This is a gridfinity bin to hold two PowerA Play and Charge battery packs. They are stored contacts-down with a gap between them and the bottom, so they should not be touching anything. I started from Akio's Gridfinity Bin empty -…
This is a battery support for Oculus Quest 2 with NEWZEROL head band. The powerbank is a PowerADD Energycell 5000mah but you can use any similar cilindrical powerbank with a diameter of about 27mm. I printed it with Pet-g and 0.8mm nozzle…
Lost the home button in my PowerA wireless switch controller. I took the options button out and modeled this based on that. I printed it with minimal supports for the 2 tabs that anchor it into place as well as a brim as the part is quite…
Thumb studs for the SOG Power Access Deluxe. The thumb stud makes deploying the blade much easier and allows for one handed deployment. It is a very small print so I recommend printing at 99%, 100%, and 101% scaling to see which fits best…
I printed on Core One with .25 layer height and 15% gyroid and it came out fine. Need a decent depth of drawer, like 14U minimum to clear.
has not been tested
There are many versions of coasters available, including this Fallout theme. However, I only have a 0.4 mm nozzle for my Bambulab P1S, and I wanted to create a version that could be printed without any issues using this equipment. The…
Holder for Spigen Powerarc charger with cord wrap. Printed at 0.2m, 15% infill, and no supports required
Summary Smartphonehalter für den T4 nach GP (1996) als Ersatz für den Aschenbecher. Zusätzlich werden zwei 0.36'' 3-Wire Spannungsanzeigen für die Start- und Zusatzbatterie eingebaut. Ich habe einen USB-C Stecker verbaut. Dieser wird mit…
Attaches to base of the PowerA Dual Charging Station to hide the annoyingly bright LED lights
I was disassembling this generic PowerA Wired Xbox One controller and at some point misplaced the middle upload button. I decided to model it and print it. Prints with no supports and fits nicely. Logo resolution can be better with a…
Summary Smartphonehalter für den T4 nach GP (1996) als Ersatz für den Aschenbecher. Zusätzlich werden zwei 0.36'' 3-Wire Spannungsanzeigen für die Start- und Zusatzbatterie eingebaut. Ich habe einen USB-C Stecker verbaut. Dieser wird mit…
I was disassembling this generic PowerA Wired Xbox One controller and at some point misplaced the middle upload button. I decided to model it and print it. Prints with no supports and fits nicely. Logo resolution can be better with a…
Remix of a skadis mount using the HSW attach anywhere double mount. It isnt perfect/clean but it works :)
For anyone who has a PowerA Moga grip, and may want to play games in portrait orientation with a controller e.g. Nintendo DS emulation on Delta emulator. I did a quick job for it, so it just slides onto the preexisting Moga clip. It has…
