61 modeli
Case for replacement PowerBook 1XX (140, 145, 145B, 150, 160, 165, 165c, 170, 180, 180c) battery using a 3rd party battery pack. Assembling a full battery will also require 3/16" copper strip which must be bent to fit the open corners of…
If you have a PowerBook 150, its plastics are probably crumbling – especially in the display assembly. This is an assortment of repair pieces that you can glue in. It includes: --Replacement hinge brackets for the rear display housing, to…
this is my pass at a shim to reinforce the 1400’s Display Housing / Hinge. I am not an engineer, just a hobbyist; please feel free to remix & re-share. the complex lower profile is to fit around existing structure, using those pieces as a…
Replacement I/O Door for the back of PowerBook 180. (Might fit other models, let me know; i only have the 180.) Use this to replace a missing door, or remix into a custom version. Share & enjoy. I printed from PETG; the little side pegs…
This adapts 15V, 2.0A USB-C Power Delivery power supplies to the 7.5V, 2.2A barrel jack on the PowerBook 160. I would assume that it works on other PowerBooks, but I haven't tested it. Of course, this can all be adapted to supply…
The batteries for the PowerBook 500 series are, at this point, over 25 years old and starting to leak. Fortunately, the outer cosmetic covers are designed to be separated from the battery pack. Unfortunately, though, they won't stay on…
This is the stock case included in the BlueSCSI repo created by Androda and uploaded here with permission. BlueSCSI models 2022.11b, 2023.10a. Select the file that matches the model printed on your PCB.
Apple's Macintosh PowerBook 1400 has a common failure these days -- the thin brackets that hold the front bezel to the CD-ROM drive module tend to crack and break. Since the machine is from 1996, brittle plastics are to be expected, so…
This is remix of the original bracket to accommodate a wider IDE drive optical board. Theoretically, it should still work with the slimmer IDE boards too. The original designer has stated that the original design will work with the IMac…
If the standoffs securing the display housing on your PowerBook Duo 2300c have finally crumbled, these replacements should get you sorted. You'll need to snip away what's left of the original ones, and keep the brass inserts. Sand down…
the PowerBook 180 case interior is intriguingly minimalism. There is very little actual structure; some components are held in place simply by being stuffed into the case itself. The hard drive has no sled, or even screws—only two tiny…
This is a model of the battery for a Macintosh PowerBook 1400. It fits the existing battery bay, and includes the appropriate slots to align and latch into place. I am not an engineer, just a hobbyist. You can print an entire battery and…
This is the battery slot cover for Apple PowerBook 500 series including 520/520c/540/540c. You will need to supply a small spring. Includes frame for when the cover is used without a battery (to just cover the slot).
Apple Macintosh PowerBook 140-180c - Main Battery Cover
This is a replacement rear port cover for an Apple PowerBook 5300 series laptop.
These are various replacement plastic mounts, etc for the pieces that normally break off on an Apple PowerBook 5300 series laptop.
So i worked on this for a few days to find a solution to properly mount a msata to ide adapter in my powerbook pismo. Things can certainly be improved in terms of used material. I printed with PETG and i can just "click" in the adapter.…
This replaces broken plastic standoffs in the chassis of the Apple PowerBook 160. Will probably fit other same generation PowerBooks but only tested with the 160. Transfer the brass inserts from the stock standoffs. You can superglue or…
These are display hinge mounts for the Apple PowerBook 500 series including 520/520c/540/540c. There are other models that have been posted but these models are meant to use a M2.5 brass bushing insert (you can find these on Amazon). The…
right and left feet for powerbook 100 series laptops. locking mechanism was modeled and functional.
This is the cover for the battery slot on a PowerBook Duo. This model is made for the type of Duo battery where the cover slides onto the battery itself.
A battery cover for the PowerBook 140, 145, 150, 160, 165, 165c, 170, 180, 180cPowerBook 140, 145, 150, 160, 165, 165c, 170, 180, 180c. Print face down with supports for the side tab.
Print in TPU with solid infill If your printer is well calibrated, it should pressure fit into the hole with no glue required, but double sided tape or super glue works if its not as perfect of a fit.
This is a replacement front bezel for the Apple PowerBook 500 series (520/520c/540/540c). It gets under the display where the microphone is.
Most people that have had an Apple Power Book for some years probably know that the power supply have a weak spot near the connector that plugs into the computer. The cable simply opens up and shows exposed wires which isn't so good. I…
Apple Macintosh PowerBook 100 - Telescopic Foot B (Left)
Apple Macintosh PowerBook 140-180c - Right Leg
Apple Macintosh PowerBook 140-180c - Left Leg
The required metal shield can be obtained searching for an RCA shield, or you can make your own via a 10mm stainless steel tube with 0.5mm thickness. You will also require some crimp pins and a 5 wire cable with diameter of 5mm.
Apple Macintosh PowerBook 100 - Telescopic Foot A (Left)
Apple Macintosh PowerBook 140-180c - Screen Hinge Cover
The original bracket by Eric Helgeson was 2mm shorter than my Powerbook 180c's old 160MB Quantum HDD. that let it move around inside the case and jump out of it's mounting pegs. I extended the walls to fit the space more. All nice and…
This model was made because I had a leaking battery in my Powerbook Duo. I did not want to rebuild the battery, but I did not want a leaking battery inside of my powerbook, so I made a dummy battery which helps provide structure to the…
Print with a brim no supports
This is a replacement side bumper for the Apple PowerBook Duo. The stock one deteriorates over time so this is a replacement.
This is a model of the original hard drive mounting bracket inside a PowerBook G3 (Wallstreet & PDQ, c. 1998). I modeled this to make a variation (to mount and SSD and some other pieces in the existing bay). The original has a slightly…
This is a replacement for the little bumper foot that goes on the bottom of the legs of an Apple PowerBook 160 (and similar models).
If the casing for your PowerBook Duo power adapter cracked/broke, or you intentionally broke it in order to open it up to recap the power adapter, then this model is for a replacement case for the power adapter. The exterior is not…
brightness and contrast sliders for powerbook 100. printed with supports.
Apple Macintosh PowerBook 140-180c - Vent
The service manual for the Apple PowerBook Duo shows a battery contact alignment tool for aligning the battery contacts when disassembling the PowerBook Duo. This is an attempt to recreate that tool based on the pictures in the service…
My powerbook was missing one foot, so i decided to replace both. There is a tiny ridge on the “inside” to facilitate snapping in place, so print with support whether you print face up or face down.
Required parts: M3 screw, nut(any kind) and washer(preferably plastic to avoid scratching) Both pieces from the STL Superglue A piece of paper if you use a metal washer and you're worried about scratching Here's a guide on how to apply…
Print with a brim no supports
This is a replacement hinge mount for the Apple PowerBook Duo. You can super glue or epoxy it in place and use the stock brass inserts with it.
Apple Macintosh PowerBook 1xx - Modem Bay Platform
Apple Macintosh PowerBook 100 - PRAM Battery Door
Apple Macintosh PowerBook 140-180c - Screen Hinge Cover
Model by TomB - uploaded with permission.
This is a replacement ADB port cover for the PowerBook 3400c. The port is found on the left side of the laptop. I have found this port cover to be missing on a lot of PowerBooks so made this part based on pictures I have seen. Because I…
The drive and battery bay latches on the bottom of the PowerBook 1400 are very brittle, and prone to breaking. Print them yourself at home, and never run out! Equivalent to replacement Part 922-3304: Latch, Bottom Case, PB 1400 Print…
This is a replacement center clutch cover for the PowerBook Duo series. The center clutch cover breaks easily as it was originally intended to be a disposable part. This model recreates it.
This replaces the little cord clip found on Apple PowerBook Duo chargers.
This is a mounting bracket for ZuluSCSI compacts (laptop version) and the Apple PowerBook Duo.
This is the rear modem port cover (left side as viewed from the back) for a PowerBook Duo 2300c. This does not include the center screw cover. Print with rafts and 100% infill. You'll also need to use supports. Alternatively, to prevent…
This is the hard drive bracket for the PowerBook 500. Since plastic doesn't obviously have the rigidity of sheet metal, the design is slightly different to provide more rigidity.
I needed a RAM cover for my 12" Powerbook G4, but couldn't find any that weren't more expensive then I was willing to pay, so I made my own. Figured I'd share it with everyone else too.
This is a caddy/carrier for the ZuluSCSI Laptop Blaster SCSI hard drive emulator, revision 2026a or later, for use in a 100-series PowerBook. Rev 2026a moves the 50-pin connector to the underside of the board so that it fits every…
This is a mounting bracket that allows installation of a BlueSCSI V2 (Powerbook edition) in a Macintosh Powerbook Duo.
This is a replacement front bezel for the Apple PowerBook 500 series (520/520c/540/540c). It gets under the display where the microphone is.
