Liczymy pasujące modele…
This is a remix of https://www.thingiverse.com/thing:3669328 . I've gotten permission from the original creator to post this remix. I've made a simple edit to the STLs to remove the raised edges from the bottom to allow compatibility with…
This furniture set reuses the existing stock screws, and handguard retaining pin. Hardware required for the magwell and carry handle respectively: 4- M3x10mm Flat Head Screws 2- M3x20mm Flat Head Screws 3- M4x35mm Socket Head Screws 3- M4…
Fits common P-Mag AR / 5.56 / .223 magazines and who knows what else. These can attach to a belt, screw to a wall or cabinet, belt attachments, paddles and misc. My modern P-mag's fit “just right” and the last 5mm insert locks them in. My…
20-40% infill 0,2 layer with support. ~2hours to print. give a like and have fun to save money :)
The built in stand on my Arrow TR550 hot glue gun failed. So I designed a new one with a wider base. Now it doesn't tip over immediately like it did with the original stand. It prints standing up, and uses two M3 bolts to act as the…
Onkyo AV receivers tend to fail after some years of usage. Most of the time the HDMI board is faulty. Usually, some of the capacitors went bad or there are bad solder joints at the DSP chip. The capacitors can be replaced and a bad…
This adapter enables the installation of 60mm x 25mm fans into Lenovo SR550 servers, reducing noise without affecting cooling. It uses two 30mm M4 screws for mounting at the bottom, with an option for a zip tie at the top for extra…
Adjust the size in slicer if needed. I sprayed few layer of putty and sanded it between layers before painting. I used PLA for printing and cink/zinc spray for paint. If this print made your day, a coffee-tip would make mine.…
Samsung LU28R55 Vesa mount for cable management
Add some double sided tape to stick these to the back of your TV and prevent the legs from dropping out when moving
Adjust the size in slicer if needed. I sprayed few layer of putty and sanded it between layers before painting. I used PLA for printing. If this print made your day, a coffee-tip would make mine. https://ko-fi.com/nsharif
These are the brackets I designed for my SO3 XXL and Uxcell R55 drag chain brackets. My HDZ is the first gen version, so the bracket for that one will have to be redesigned. I don't have the newest version, so you'll have to do it. There…
The Mount consists of two parts, the main body and the Mountingplate which interlock with a dovetail. I printed this Mount on a Prusa Core One, with PETG. To properly attach the Mount to the Skadis Board, the T-Clips by Line Arc Line are…
Here I designed a headset mount for a Samsung LU28R55 monitor. The monitor is virtually featureless for finding anything to hook or datum off of, so I had to make the model into a few parts so that I could use the 75mm square VESA…
Tyto 3D tištěné krytky jsou určeny pro zakrytování kovového pantu na hliníkových kufrech Shad TR55 . Originální pant má relativně ostré hrany , které mohou při manipulaci zachytit oblečení, poškodit textilie nebo způsobit drobné poranění…
Fits common P-Mag AR / 5.56 / .223 magazines and who knows what else. These can attach to a belt, screw to a wall or cabinet, belt attachments, paddles and misc. My modern P-mag's fit “just right” and the last 5mm insert locks them in. My…
adapter to go from a threaded Thruxton 1200 R stem nut to a tomtom rider 550 for better central mounting Unknown what stem nut is on mine. step file is included in case you have to change it. Holes best marked and drilled rather than…
