Liczymy pasujące modele…
Ich habe mir dieses Model herrausgesucht um einen Bechtest zu machen. Dafür habe ich die Größe auf 30% herrunter skalliert.
Wydruk około 0,37 €–0,46 € nettoWstępna wycena jednego wariantu
https://www.printables.com/model/1122014-tazne-zarizeni-rc-110-towing-device-110-rgt-rescue it is necessary to describe the parts when printing! Pneu https://a.aliexpress.com/_EQaJNvO PLA AURAPOL 25% infill 3 walls .02 layer height no…
No chassis modification required for installation simply unscrew and replace a couple of screws with 2mm londer ones, for the shock mounts use 3mm nuts and washers to prevent chassis from scratching, usage of washers is recommended for…
Prints without supports. Minimal painting makes it look a lot better. I used a black marker to hide the edge of the engine bay and servo tape to install the print.
RGT crusher (will most likely work on other models like fms, ecx, element etc) axle link mounts
Software and assembly video here: Case is ideally held together by either melting with a soldering iron or just using glue. Electronics Used (Including Purchase Links) WeAct Studio STM32 Core (STM32F405RGT6):…
Hin und wieder ist auch ein Schild ok :) Druckeinstellungen: - Material: PLA White, Black, Red - Nozzle: 0.4mm - Layer: 0.2mm - Profil: 0.2mm speed - Supports: keine Mit Leidenschaft gemacht von Xargas! Gefällt dir, was du siehst? Du…
There is a small panel hiding a spot for a light bar in the front bumper. It is held in place by a few small plastic pegs that are easy to cut. The inside of the bumper has 4 screw holes. 4x M3x8 screws should be more than enough to keep…
Repair piece for Thrustmaster RGT pedals. Material ABS Layer 0.10mm DETAIL Printed on Prusa MK3 Need M5 bolt
Installs using the original screws. Remove bumper first for better access.
Have you broken the original rear bumper mount? Print this model!
Soporte para montaje de leds en Crawler RGT EX86100.
Software and assembly video here: There are two sets of parts for the top+bottom+buttons depending on the screen size you want. Case is ideally held together with 12mm M3 self tapping screws. Electronics Used (Including Purchase Links)…
There was an empty space behind the cab, it asked for something, and the fuel tank is the best solution. Tank is held on 2 mounts - left is smaller, and right is extended as there is also exhaust muffler that tank has to avoid. Mounts are…
A simple holder for the battery in the front to get more weight on front axle but cg will be a little higher… Works with smaller batterys, i.e original 2000mah 2S You need to drill the holes for the screws
Hello. This is the sparewheel holding nut for RGT Crusher. It is made to look like some reallife easy-release nuts. Easy to print w/o supports and it screws directly on the sparewheel screw. S.D.G.
Custom RGT Crusher battery tray for Trx 7-cell NiMH. Mounted via 2 screws into existing features on the car. It makes the CoG a bit higher, but needed to be done as trx battery wont fit corrrectly installed sideways as original battery…
Here is the mount / holder for LED lightbar RGT-P860084 for mounting on the RGT Crusher rollbar. Use 2 screws to secure the lightbar into the mount, and the mount just clicks on the rollbar. I already did 2 expedition with it, got rolled…
Hello. I designed this short sport exhaust for RGT Crusher because, when using my fuel tank, exhaust muffler now sits lower. So the stock long exhaust wouldnt fit. This, I believe is a nice solution. S.D.G.
Chassis cover for when you remove the stock battery housing, so that there wont stay the big emptiness where dirt can enter. s.d.g.
Case a clamp na akční kameru na střešní nosič modelu RGT LandCommander, pro sestavení je třeba: 1x šroub M8x40 nutt 13mm, 1x šroub M8x16 nutt 14mm, 2x vějířová podložka 8mm, 2x normální podložka M8, 2x křídlová matice M8.
No chassis modification required for installation simply unscrew and replace a couple of screws with 2mm londer ones, for the shock mounts use 3mm nuts and washers to prevent chassis from scratching, usage of washers is recommended for…
A spool cover to fit for a servo winch in the front of the RGT EX 86020 Intruder To prevent the wire to tangle when not under tension I used some longer m3 screws for the servo and a litle triming of the bumper holder, there is not a lot…
