P
Printablesexperify3d
Mazda CX7, CX9, RX8, RX3, RX6 Motor window gear
Replacement for the window motor gear. Works as intended, printed with PETG-CF.
- Pobrania
- 312
- Polubienia
- 32
- Ocena
- 5
Wyniki wyszukiwania: rx8
Liczymy pasujące modele…
P
Printablescs900
FD3s adapter for RX8 DBW pedal
This bracket allows you to mount a RX8 DBW pedal into the FD3s RX7 chassis without modification to the chassis or pedal. Should be pretty easy to print, and I would suggest doing it in ABS or PETG only and use a heavy infill. You'll want…
- Pobrania
- 131
- Polubienia
- 12
- Ocena
- 0
P
PrintablesVicccccccccc
Mazda RX8 Taillight Gasket
I got tired of paying $15-25 every time I had water get into my taillights for new gaskets, so I modeled this using my OEM one, and spent near that in prototype prints. The goal is to 'squish' it with the taillight housing so; Print in…
- Pobrania
- 110
- Polubienia
- 12
- Ocena
- 0
P
Printablespeter.skotte
FrSky RX8R Mount - Flat
FrSky receiver mount - flat Category: Hobby
- Pobrania
- 67
- Polubienia
- 5
- Ocena
- 0
P
PrintablesGeraffel
G-pulley/B-screw setting tool/Rear Derailleur Alignment gauge for GRX RD-RX820 RD-RX822
To adjust the B-screw of the rear derailleur RD-RX820 and RD-RX822. Set the gap between the largest pinion and the guide roller: 34 Teeth - 10mm 36 Teeth - 6mm There is an STL and a STEP version, the shape is the same.
- Pobrania
- 65
- Polubienia
- 7
- Ocena
- 0
P
PrintablesRapidAnalysis
Xerx86 Enclosure
Darius is a Nano-ITX Intel® based single board computer with a ram slot, 2 mSata slots, and active cooling. This enclosure can be printed or modified to fit the Darius or other Nano ITX single board computers by customising its removable…
- Pobrania
- 53
- Polubienia
- 6
- Ocena
- 5
P
Printablesjohn
hood / bonnet latch Mazda rx8 rx-8 raiser (re amemiya)
A 7mm spacer for the bonnet latch when installing a re amemiya bonnet / hood on a Mazda RX-8 Because the hood will be out of line without this spacer i designed it for a friend. Printed best be in ABS or PETG
- Pobrania
- 43
- Polubienia
- 5
- Ocena
- 0
P
PrintablesSirHamsterAlot
Rx8/13B Rotor/Stationary Gear Press tools
Some printed press dies for pushing bearings in/out of rotors and stationary gears for the 13B engine. For best results print in ABS or similar strong filament with 100% infill.
- Pobrania
- 41
- Polubienia
- 7
- Ocena
- 0
P
PrintablesBlockatiel
Rx8 SSV actuator bush
The original bushes wear out and make an annoying noise. Sourcing replacements can be difficult so I made this. Recommend printing in Nylon or other high temperature, low friction material. If printing in hard material, advise splitting…
- Pobrania
- 40
- Polubienia
- 5
- Ocena
- 0
P
PrintablesMotodenta
RX8 PZ Prodrive wing badge
RX8 PZ aka prodrive wing badge
- Pobrania
- 24
- Polubienia
- 2
- Ocena
- 0
P
PrintablesSwimminginprojects
Mazda RX8 Renesis Oil filler neck
With a groove for an o-ring in the bottom of the lid and on the bottom of the oil neck. When the OEM solution is not applicable. Connector on the neck for a fitting for a breathing hose. Designed for a Wankel/Renesis-conversion project…
- Pobrania
- 22
- Polubienia
- 5
- Ocena
- 0
P
PrintablesAlan Kim
RX-8 RX8 Diff Axel Seal Driver Tool
Tool to install axel seal into RX-8 Differential. Designed to be used with air hammer seal driver tool, but can be used with any metal driver.
- Pobrania
- 8
- Polubienia
- 5
- Ocena
- 0
P
PrintablesCan Soykal
Serpent SRX8 GT Battery Box
Serpent SRX8 GT 23 onwards have an open type battery mount. This is a closed box for added protection
- Pobrania
- 6
- Polubienia
- 6
- Ocena
- 0
P
Printables
Xerx86 Enclosure
Darius is a Nano-ITX Intel® based single board computer with a ram slot, 2 mSata slots, and active cooling. This enclosure can be printed or modified to fit the Darius or other Nano ITX single board computers by customising its removable…
P
Printables
Mazda RX8 Renesis Oil filler neck
With a groove for an o-ring in the bottom of the lid and on the bottom of the oil neck. When the OEM solution is not applicable. Connector on the neck for a fitting for a breathing hose. Designed for a Wankel/Renesis-conversion project…
P
Printables
Mazda RX8 cabin filter cover replacement (Modular)
The original part has a weak point by design and eventually breaks. This model uses M3X8 bolts to attach the fingers to the main body of the housing using M3 bolts. This way if the part breaks again, you only have to reprint the fingers…
P
Printables
Držák na příposlech RX8 / Holder for Flacarp RX8
Držák na příposlech RX8 / Holder for Flacarp RX8
P
Printables
FrSky RX8R Mount - Vertical
Vertical mount for FrSky X6 & X8 series receivers. Category: Hobby
P
Printables
Mazda RX8 rear license plate bolt clip
Broken/seized rear license plate bolts? Don't want to remove your bumper to fix it properly? This is what you need. Can't say what year range will work but if the holes in your rear bumper are 15mm x 10mm this should work. Meant to take…