Liczymy pasujące modele…
These were designed for my ‘96 Subaru Sambar. Many pieces aren’t made so the only option is shipping used from Japan, so figured this was a good option. Still new with Fusion, and my reference pieces are old and the tail gate has some…
Subaru sambar Shifter bushings to my KS3 sambar 1995 May or may not fit KS4
Subaru sambar oil seal install tools to get the seated properly
Subaru sambar door handle Test fit video
This is a basic model for an insert into the upper dashboard pocket on a KS4 (90's) Subaru Sambar. I used it with a phone holder model I found on here, though I don't see it currently to give credit. But would be a good base for a gauge…
Subaru sambar Gear linkage bushing rear 4 pcs needed and 4 orings 14x19x2.5mm Abs or other heat resistant material recomended
i did this for an hour in tinkercad sp sry for anything that looks bad especially the right side and i also hate how the top it a little too tall sinc it came from teh van version. Im printing it now will post update photos in a few hours…
Subaru sambar speaker screw clip 3mm hole and 4mm hole depending on what screw you using In hot climate print in ABS or ASA
A model of Isambard Kingdom Brunel, adjusted to be printable without supports. If your printer has good cooling, this model will print well without supports. Roughly 145mm Tall Pictured model printed in Esun Black PLA and Prusament Viva…
I printed in ASA for heat resistance and durability. Printed on Sovol SV04. Friction seems to hold it in place pretty well, but you could aways add some double-sided tape or Velcro to the rear bottom tab to hold it more secure. I designed…
This is a tray made to hold two cup holders. Print the tray first standing up, then cup holders separately and glue on. At least that gets the best looking print in my opinion. Remix to your hearts content. Printed in PETG.
this model is a close replica of the original inner door handle for my 2000 Subaru Sambar Kei truck. it uses the original bushings for the fasteners, they could be modeled and printed, but the original machined parts would be better to use.
My Sambar's mount was broken so with some measurements and a photo reference, I was able to create this model. It snugly fits the flare my truck came with. No support material should be needed for a properly tuned machine.
This is a blank as well as one with holes for buttons. It fits in the location of the stock coin holder.
Dad needed a mount for the aftermarket radios mic. Slots into one of the two open spots behind steering wheel. Socket is sized for microphones that typically come with Pioneer head units. I used auto tree supports. STEP provided for…
Cover for Dome/map light on a 94 KS4 Sambar. Print in Clear PETG, and _probably_ replace the bulb with an LED bulb. Change infill settings for interesting patterns. This isn't a great fit- ideally the top section would have a 1mm bow up,…
This is a mount for the Cobra 19 mini CB radio. Simply slot in after removing your ash try.
Collection of models for the KS4 sambar. Included in this: Headlight mounts These mounts cover the left and right turn signal and headlight area and mount a 5.75" round headlight. I used something similar to the following:…
I needed to mount a slightly larger radio under my dashboard and due to small working clearances, the best way to get the flexibility and angle I needed was with a RAM ball-and-socket mount. By using the AMPS plate pattern, I figured this…
this is so there is more of a variety if you have a Matchbox subaru sambar, or to use it in dioramas
this is so there is more of a variety if you have a Matchbox subaru sambar, or to use it in dioramas
Subaru sambar Shifter bushings to my KS3 sambar 1995 May or may not fit KS4
