Liczymy pasujące modele…
Base needs supports in order to print the zip tie holes correctly. I may post a model without them so no supports would be needed. I can easily change the angle of the screen, currently it is tilted back about 18degees. Just send me a…
I created a housing for my WT32-SC01 touchscreen with ESP32 that I use with the FreeTouchDeck software. Both parts print without support. Used Parts: WT32-SC01 4 x M3x10 counter sunk screw Software:…
Need 4 M3x12mm screws. The usb charger module is only supplying 5v to the WT32. Category: Electronics
This is a 3D model of the WT32-SC01 microcontroller board with 3.5" touch screen. It is not a case and it is not for 3D printing . Use this model to integrate it into larger designs in your preferred CAD program. I originally found a…
Case to hold your 3.5" TFT Arduino screen
I needed to install a WT32-SC01 Plus device to replace an old outdated alarm panel. Thankfully some pre-existing models existed, but needed some finessing to work. I merged the two models, and added some space to include some double sided…
This is a base for the WT32-SC01 Plus module. The design is made for the FriendlyStack Reminder project (please support) but will obviously work for other things as well. In contrast to the original design, this model has a larger base so…
(work in progress) Supports are necessary for the front part. Organic supports like in Prusa Slicer work fine. In order to mount the module the display needs to be separated from the board. The large hole in the backplate can be used to…
This is a case / stand for the WT32 SC01 Plus Display module. The module just snaps into place and there is a reset button on the back. The stand can be attached to a surface using screws, magnets or glue. The model is optimized for SLS…
This is a lightweight Jabra Evolve 20 30 hsc016 headset desk holder for those who are mad about this piece jumping off the table 2 variants - one with a holder only from one side and a second with holders from both sides for better…
This is a housing for the ESP32 board WT32-SC01 with 320x480px LCD and two sensors: - SEN5X (PM, VOC, Temp, Humidity, NOX) - all SEN53, 54 and SEN55 have the same form factor - SenseAir S8 (CO2) The back cover is holding the sensors in…
This is a case / stand for the WT32 SC01 Plus Display module. The module just snaps into place and there is a reset button on the back. The stand is self standing but can also be attached to a surface using screws, magnets or glue. The…
This is a case / stand for the WT32 SC01 Plus Display module. The module just snaps into place and there is a reset button on the back. The stand is self standing but can also be attached to a surface using screws, magnets or glue. The…
The WT32-SC01 is a low cost wireless touch panel device. I have installed the firmware OXRS on this device and use it to control continuous print jobs, and query the printer through the API provided by OctoPrint. So I needed some way to…
To mount everything on the case, just look on the pictures SC01 display is connected to the power control with the cable provided for the RS485 interface. Just use green and yellow and remove black and red To mount the stand you will need…
I created this print to mount a WT32-SC01 display into a regular single-gang electrical box. The print consists of two parts: The backplate mounts to the box using the standard holes, and has pins that line up with the holes in the…
This is a basic connector for you to use to create a mount or similar for a NSC01. (These STLs are useless unless you build something for them - they are posted to get you started/ as samples) There are two STLs: a simple ring so you can…
A Remix for a esp32 (WT32-SC01 Plus) based Display in combination with OpenHASP
I created this print to mount a WT32-SC01 display into a regular single-gang electrical box. The print consists of two parts: The backplate mounts to the box using the standard holes, and has pins that line up with the holes in the…
Case to hold your 3.5" TFT Arduino screen
This is a modified version of WT32-SC01 case created by mbenten on https://sketchfab.com/3d-models/wt32-sc01-case-cfec05638de540b0acccff2091508500. I just only adopt it to the newest version of WT32-SC01 3.3 in which reset switch is moved…
Having built-in WiFi is nice, but not for bed levelling and quick z offset adjustment. But it could be used for anything else. If your screen has nuts it shouldn't need the spacer. If not the spacer provided can be cut down to size in…
Description Case for WT32-SC01. Display: The WT32-SC01 incorporates an ESP32-WROVER-B module with a 3.5-inch capacitive touch display. http://www.wireless-tag.com/portfolio/wt32-sc01/ Print settings: Printed via 0.3mm layer height.
Wall/desk enclosure/mount for the ESP32+touchscreen SC01 plus: https://s.click.aliexpress.com/e/_DF2lAiP Has a hole for the reset. Snap fits the screen. Looks awesome Category: Electronics
I use several displays with ESP32 and openhasp firmware. I created a case to mount the display on my ender 3 enclosure. Following parts are also needed: Screws: 2x M3x 6mm + 2x M3x10 + 2 M3 nuts + 2 woodscrews 3x12mm Heatinserts: M3x5x5…
This is a minimal enclosure for the WT32-SC01 ESP32 Dev Board. The case was designed around the V3.2 dev board, which has standoffs on the corners. They are only used for positioning the board inside the case. Enclosure Features: Reset…
This is a minimal enclosure for the WT32-SC01 ESP32 Dev Board, that incorporates a USB-C charge controller, Li-ion battery, and power switch. The case was designed around the V3.2 dev board, which has standoffs on the corners. They are…
This is a case / stand for the WT32 SC01 Plus Display module. The module just snaps into place and there is a reset button on the back. The stand can be attached to a surface using screws, magnets or glue. The case was designed for the…
This is a case / stand for the WT32-SC01 Plus Display module. The module just snaps into place and the cable is hold in place by a specifically designed groove on the bottom of the case. An angled USB-C connector is required to connect…
