Liczymy pasujące modele…
This will fit stepper motors type 42-34 as found in many kits. Print Settings Printer: Elegoo Neptune 2S Rafts: No Supports: No Resolution: 0.15 Infill: 30 Filament: Your choice, I used PLA Notes: Print with the top plate face down…
The K10 has a poor printing quality due to the excessive play on the axis plastic sliders. A lot of the movement is caused due to the top feeding design, that restricts you small filament portions at a time. Changing the feeding direction…
In English: (Deutsch weiter unten) This is a stabilizer for the pulley below. I noticed that the deflection always had a negative influence on my prints. Since I have already developed and installed stabilizers on my other printers and…
A set of stabilization fins for sliding over the Carp Lounge Camera for the RT4 bait boat to help the camera not spin while in the water. A friend of mine has an RT4 boat and asked me to make this for him as he had had one for another…
Extended version of the "IKEA Lack Table Angled Leg Reinforcement" by @PotatoFactory corner brackets for ikea lack.
This is a stabilization bracket for the Tevo Tarantula printer. In the stock printer the Z-Axis 'floats' on the flexible shaft coupling which creates some vibrations and compromises rigidity. To install this you need 1) a standard 8x22x7…
A gyroscopic stabilizer for RC model ships. Built around a G-Power BL motor, 2225, 2000KV, 6-11.1V. Two versions available: large with approximately 110g flywheel mass and small with 50g flywheel mass. Each uses the same drive.
Poznámka: Český popis naleznete níže. English: Introduction When creating aquarium layouts, I use a substrate support grid to prevent substrate sliding, especially on slopes and in more complex aquascapes. The commonly available Invital…
Wanting to make my Boat more and more individualistic, adding different things to it, unfortunately had some negative consequence, She became very top heavy.... I experimented with varying keel designs to try and make her more stable in…
This is a stabilizer for a hario skerton clone so that the burrs have less movement. I think it will fit a genuine skerton as well but i dont know for sure. I printed it in PLA and it does make a difference.
The Jellas foldable grabber / reachers joint is pretty weak. My kids broke it within the first week. This replacement stiffens the joint. PETG is still and still flexible enough and therefore recommended. Attached Fusion 360 Archive and…
BOM : m3 screws & nuts x5 628 ZZ bearing Last time i start modernzation of my sapphire S. It's very first version of this printer. I couldn't find any proper Z stabilization, so I made my own. I put direct drive with using eva carriage,…
GE GFE26JSMAFSS Refrigerator Freezer Track Stabilization Gears Optimized for easy printability and installation with 1x M3x16 bolt and one m3 nut. Supports dependent on your machines ability to bridge, not necessary for most.
This model was made to help reinforce the idler pulley of the flsun sr delta gantry. We be swapping two of the components: Idler → 20T pulley | 25mm Screw M5 → 30mm Screw M5 The printed stabiliser should be printed solid (mostly walls). I…
(As I didn't have a long enough rectangular tube available, I used a longer end piece for the photos.) I have here two simple and inexpensive, but very effective and easy to realize solutions for frame stiffeners on old Musser M55…
Update: 10.July.2024: Small geometry changes for easier printing and assembly I have here two simple and inexpensive, but very effective and easy to realize solutions for frame stiffeners on old Musser M55 vibraphone frames. All you need…
This lets you mount your ZSA Moonlander on tripods or arms that have the stabilization pins. I'm specifically mounting mine on the SmallRig Rosette 11" Magic Arms: https://a.co/d/08LQxkpj I printed them with: 0.2mm layer height 4 wall…
Installed linear rails to get rid of flexing of the workplate of my Snapmaker 2.0. The rail holders screw into the base of the linear modules, allowing an installation without drilling the base. This model is a re-design/remix to fit…
For the broken spiral hose I have designed a stabilization sleeve.
A shelve stabilization that should prevent the board from hanging in the midsection.
Installed linear rails to get rid of flexing of the workplate of my Snapmaker 2.0. The rail holders screw into the base of the linear modules, allowing an installation without drilling the base. This model is a re-design/remix to fit…
This lets you mount your ZSA Moonlander on tripods or arms that have the stabilization pins. I'm specifically mounting mine on the SmallRig Rosette 11" Magic Arms: https://a.co/d/08LQxkpj I printed them with: 0.2mm layer height 4 wall…
The K10 has a poor printing quality due to the excessive play on the axis plastic sliders. A lot of the movement is caused due to the top feeding design, that restricts you small filament portions at a time. Changing the feeding direction…
Update: 10.July.2024: Small geometry changes for easier printing and assembly I have here two simple and inexpensive, but very effective and easy to realize solutions for frame stiffeners on old Musser M55 vibraphone frames. All you need…
(As I didn't have a long enough rectangular tube available, I used a longer end piece for the photos.) I have here two simple and inexpensive, but very effective and easy to realize solutions for frame stiffeners on old Musser M55…
suitable for all action cameras. tested with dji osmo action4 and gopro hero 5 black no supports needed. easy to print
Case for a ACT Wingo RC flight stabilization Tape the board with double sided tape in the case Category: R/C Vehicles
Made this to give the frame more stability. Category: 3D Printer Parts
This is a two-part stabilization system designed to: Compensate for uneven floors Eliminate wobble Reduce vibration Secure a shelf or rack to the wall despite plinth (baseboard) offset Ideal for workshop furniture, server racks, storage…
Same bracket - larger holes Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0.2 Infill: 15% Filament: no name PLA black Category: Other
I tired of knocking over a bottle in my bathroom all the time, so I made something to give it a wider base, while also being aesthetically pleasing/interesting at the same time. Everybody loves the Golden Ratio and powers of 2! Designed…
