Liczymy pasujące modele…
Wearable / 3D Printable An elegant crown inspired by Princess Yue from Avatar: The Last Airbender. Delicate and regal, featuring flowing curves and subtle details that evoke the ethereal beauty and nobility of the moon princess. Perfect…
Hi all, mainly designed to fit my Feiyue Fy08 since I'm using it on 3S Lipo and I don't want to destroy my lipo. Fits perfectly with my 3S 2200mAh into the lipo bay. To use it with a Socket just desolder the pin strip and solder a socket.…
5-position hot air rework nozzle holder designed with the Aoyue 888A rework station in mind, although it may fit other models. The Aoyue rework stations are made by SRA Soldering Products with a 21.5mm inner diameter on the nozzles so any…
Feiyue FY03 540 Motor Adapter This is a 540 motor adapter to fit the Feiyue FY03 RC car transmission. There's 3 mounting holes evenly spaced to fit 6 hole motors. Freecad save's been included. EDITS 18/12/17 FLAW FOUND! The 2 screws that…
I do comprehensive 3D scanning and you can see some of my results here. The models are partially edited with AI due to small or missing details. If you are interested in my work and have a specific interest, you can write to me and my…
Cut the flat back cover off of the original solar panel, leaving the rectangular shaped rim to slide this enclosure over. Remove all existing electronics and solder the panel output to a buck converter set to about 5.75 volts if you are…
Similar designs existed for other brands of soldering stations, but the holes were not big enough to store tips for AOYUE. This storage container will fit 12 tips with ~6.5mm diameter. There is relief in the cap to allow 2 long tips at…
A simple dial plate overlay for the Aoyue 469 soldering station. Shows estimated temperature in ℃ instead of just number 1-8. Disclamer - I did not come up with these temperatures, nor have I verified that they're accurate. I literally…
This Gridfinity 2x3 holder for the soldering tips and hot air nozzles of the Aoyue-968A solderingstation has four spare holes for additional soldering tips. It offers space for all four hot air nozzles. It was designed with the Fusion360…
Engine spare part for Feiyue FY-03 Eagle RC Car. 1:10 ;)
Here's a bin that stores two nozzles for an Aoyue hot air rework station. Features: holds two nozzles occupies two Gridfinity units printable magnet and screw holes on bottom crush ribs on magnet holes hold magnets tightly I modeled this…
I had a 120mm tires that i wanted to apply to stock wltoys 12428 discs, unfortunately stock discs has different diameter for the beadlock rings, this thing could help you if you want to do the same. See results here: I used tires from an…
Upgrades for the UYUE 946c Preheater and Hotplate
the light used is this one https://a.aliexpress.com/_Ewh2c6Q
The original Aoyue WQ tips are shorter and nicer, but T12 tips are way cheaper and easier to source, so I have for a long time wanted to do this mod to be able to use them. WARNING : The thermocouple in T12 tips is different, so you have…
The original Aoyue WQ tips are shorter and nicer, but T12 tips are way cheaper and easier to source, so I have for a long time wanted to do this mod to be able to use them. WARNING : The thermocouple in T12 tips is different, so you have…
5-position hot air rework nozzle holder designed with the Aoyue 888A rework station in mind, although it may fit other models. The Aoyue rework stations are made by SRA Soldering Products with a 21.5mm inner diameter on the nozzles so any…
Yuemi YMI Ergonomic chair armrest. TPU Inill: 5% Layer Height: 0,3 Width: 0,8 Nozzele: 0,8
Feiyue FY03 Large LiPo Batt Box Mod This is a complete Lipo Tray that's got a space (143mm x 28mm x 50mm) for a much larger than stock LiPo. This is for the Feiyue FY03 chassis. It's a 3 piece assembly that doesn't require any extra cuts,…
Feiyue FY03 MG995 Servo Mod This is a vertical adapter for the Feiyue FY03 to fit a TowerPro mg995 or other servos the same size. You need to mark out and drill/melt 3 new holes in the base of the car to fit this new mount for your…
Feiyue FY03 Radio Box A simple box intended to hold an RX Receiver .This attaches to other mods and WON'T fit into the stock vehicle by default. Links to mods this fits onto. https://www.thingiverse.com/thing:2623759…
After purchasing a SRA Soldering Products 852A++ reflow station I discovered that the included vacuum pen clip was woefully inadequate. I designed a simple replacement part requiring only 2 M4*10mm bolts (SHCS). Print settings: Supports…
Hi all, tried out the Feiyue FY08 just 4 fun. Since I'm using this toy with a 3s Lipo it went to a wheelie machine. Therefore I designed a Wheelie bar. All screws can be used. Only the back sign holder has to be removed. For the wheels I…
Based on someone's idea, I created my own version of a bolt cover for scooters from China like Laotie, Boyueda and others. No text or logos. You can finish it yourself in slicer. Install First put the version on the nuts (hex). Lightly…
A tray to store the nozzles that came with the Aoyue 852A++ Pro. Includes compartment for suction/vacuum tips with a lid. Mounts with the existing vacuum tube mount screws and replaces the tube mount.
Divertido llavero con forma de Rayuela, Pata coja, Reina mora, Golosa, Carroza, etc. Fácil de imprimir.
This is a stand for Aoyue soldering tips. It holds 9 tips. It cannot be used as a floatation device, and will not freshen your breath. It makes a lousy spatula for pancakes. It does not remove stains from carpets, and it will not defy the…
