Universal 20cm Fan Mount - Noctua - NF-A20 PWM
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Adapting a 20cm fan to a desktop, reducing noise. Detailed instructions for assembly and side panel modification.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 34
- Makes
- 0
- Views
- 327
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Computers
- License
- Creative Commons — Attribution — Share Alike
Universal 20cm Fan Mount - Noctua - NF-A20 PWM
I really like the concept of the 20cm cooler mainly because of the following: it's quiet. Since my computer is right next to me, I decided to design a project to adapt a 20cm cooler to my desktop.
I created an adapter that is universal and can be used on the side panel of any desktop. Please note that this requires some cutting on the side wall of your desktop case.
Step 1 - Assembling the Adapter:
Print the parts in pairs (part 1 and part 2) and connect them. At first, you don't need glue; the connection is quite stable. I used a bit of adhesive like T-1000, T-6000, or T-7000—use whatever you're comfortable with. For assembly, I usually use a nylon hammer and a plier without serrations.




For the filter preparation, I recommend taking the female part and applying some glue in the groove.


After applying glue in the groove, cover the female part of the filter with a pantyhose.

After this step, attach the male part to the female part and use clamps or some kind of weight to let the glue dry.


Once the glue is dry, trim off the excess pantyhose, and the filter is ready. It can be reused multiple times or remade if needed.

Step 2 - Adapting the Case: This part may vary depending on your case. My case has an acrylic side panel, and I used to have two 12cm fans on that side. I decided to replace my two 12cm fans with a 20cm fan.

Remove the side panel of your desktop, bring it to your work area, and, using the backplate, mark the cuts and holes with an acrylic marker. I printed a backplate with half the thickness to use as a guide, which made marking the holes easier.


Since I was working with acrylic, I started by drilling large holes in the corners to reduce the chance of cracking. I also used water to cool down the cutting and drilling process to avoid cracks.

After drilling, I used a Dremel to cut along the marked line, being careful and applying water occasionally for cooling, until the section I needed to remove came out of the panel.


After that, I drilled the holes for the 3mm screws in the four marked points. Two important things here: personally, I recommend doing this before cutting with the Dremel if you're working with acrylic. I forgot to do it, and one of the screws ended up causing a crack—nothing that compromised the structure, but not ideal either. Always be careful, go slowly, and use sharp drill bits. The crack happened because I was in a bit of a hurry while drilling.


In the end, I used a deburring tool to remove sharp edges from the Dremel cut.

Step 3 - Mounting the Cooler to the Desktop
Start by placing four M3 nuts into the deck plate and four M3 nuts into the mounting frame.




Insert four M3x40 screws to secure the frame to the backplate through the side panel of your desktop. The screw length may vary; in my case, the M3x40 worked well because of the acrylic thickness.



Place the frame on the table and align the side tunnels of your desktop panel with the screws on the frame.

Next, place the backplate in the correct position and finish screwing the frame to the backplate, ensuring that the side panel is sandwiched between them.



At this stage, I attached the cooler using the Noctua mounting rubbers, as they reduce the vibration transferred from the cooler to the case, which helps to reduce noise.

Finally, I like to use a filter to reduce the number of times I need to clean my computer. So, I used four M3 x 40mm screws again, attached them to the filter, and then secured the filter to the predetermined holes.


Final Result I am very happy with the final result, mainly due to the significant noise reduction, as the desktop is right next to me. If noise is an important factor for you, this could be a good solution.