ESP8266 / ESPhome Air quality monitor
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Forced air monitoring device to measure several parameters
- Rating
- 0 / 5
- Likes
- 3
- Downloads
- 35
- Makes
- 0
- Views
- 412
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- Creative Commons — Attribution — Share Alike
I wanted to create a forced air monitoring device to measure several parameters in my living space. Fan is used to force air in and around the sensors, this way stagnant air or heat-soak is not an issue.
Measures Temperature, Humidity, Pressure, Co2, TVOC, VOC, LUX and Presence.
OLED can display values directly and ESP also serves values directly to ESPhome/Homeassistant or other home automation system.
Boards/Sensors can be omitted as per requirement.
Fan can be switched on/off using GPIO15, it could also possibly be used to modulate the fan although the fan chosen has an audible whine using PWM. Therefore using +3.3v as supply, to make the fan quiet. Open to any suggestions on quiet radial 30mm fans.
I have attached an ESPhome YAML file for configuring, I have omitted LD2420 and AGS10 sensors as I have not received them yet. In this YAML I have averaged Temperature and Humidity between AHT20 & AHT21 for more accuracy. When using this supply your own esphome:, api:, ota:, and wifi: credentials.
Parts list: (Links are exact items used, replacements can be used just be sure dimensions are the same)
ESP8266: https://www.aliexpress.com/item/1005007598012744.html
ENS160+AHT21: https://www.aliexpress.com/item/1005006162039607.html
AHT20+BMP280: https://www.aliexpress.com/item/1005006109113441.html
SGP41: https://www.aliexpress.com/item/1005006746827606.html
AGS10: https://www.aliexpress.com/item/1005007369166584.html
TSL2561: https://www.aliexpress.com/item/1005006047383759.html
LD2420: https://www.aliexpress.com/item/1005006337788084.html
NeoPixel: https://www.aliexpress.com/item/1005005862049283.html
Fan: https://www.aliexpress.com/item/1005002449192337.html
BS170:
M2x6mm(2pcs):
M2x12mm(4pcs):
Wiring:
AHT20+BMP280: (+) (VCC) to 3.3v, SDA-GPIO14(D6), SCL-GPIO12(D5), and GND to GND.
Rest of sensors: (+) (VCC) to 3.3v, SDA-GPIO4(D2) SCL-GPIO5(D1), and GND to GND.
FAN: (+) to 3.3v, (-) to pin1 on BS170, pin2 on BS170 to GPIO15(D8), and pin3 on BS170 to GND.
NeoPixel strip: + to 5v (VIN), DI to GPIO2(D4) and GND to GND.
When assembling it is easiest to wire everything on the bench using about 60mm(~2.5freedom units) wires. I used thin “wire wrap” leads for everything, as these are single core and easy to work with.
Quirks! Because the AHT20 & AHT21 share the same address we need to use two separate I2C buses. OLED is not well documented, but figured out the following:
I2C OLED & AHT20+BMP280 is SDA-GPIO14(D6) SCL-GPIO12(D5)
I2C Rest is SDA-GPIO4(D2) SCL-GPIO5(D1)
I2C Address list:
ENS160: 0x53
AHT21: 0x38
AHT20: 0x38
BMP280: 0x77
SGP41: 0x59
AGS10: 0x1A
TSL2561: 0x39
OLED: 0x3C