LED Spice Rack

I decided to redo the spice rack in the kitchen with RGBW strips and some fancy-ish mounts.  I think it turned out good. The files are very specific to my situation, but everything you need is below.  I included STEP files as well so if you want to alter for yours :) if you have any requests, just message me. 

All the files are included in two folders: STL and STEP, you may have to expand them to see the files.


This setup is designed for 15.5" x 5" glass shelves, in a 5" deep area/cupboard. 
The thickness of the glass I used is 1/8” thick. 
 

All of this is designed so the shelves can be removed easily if need be. 
 

Materials use:
Screws for the mounts: https://a.co/d/aMcgt7v
Mirrors for the edges: https://a.co/d/hJYdOJX
JST connectors for LEDS: https://a.co/d/6etSjGt
RGBW LED Strips: https://a.co/d/7o3KJw3
3M VHB Tape: https://a.co/d/cBLtWua
 

This printable includes multiple files, I will try to explain them.

Alternate Glass Mount You can use this instead of the mounts that the glass slides into to.  The glass can just sit on top of this one, (Wire Hiders, etc, are not compatible with this)

Drill Guide Jig Is used to make sure the holes are exactly correct.  Use a very small drill bit to pre drill the holes for the screws to have a perfect alignment.  The holes for the mounts for the screws are big and can be difficult to get straight with only using the screws and a screwdriver.  This will allow you to be way more precise.

LED Hider_Right & LED Hider_Left are used to mount to the glass to conceal the wires.  They have two pads, which is where the VHB tape from 3M would go to mount them to the glass. Use in conunction with “Wire Concealer” as seen in the second photo below.

Main Mount_Middle Used to mount between the very bottom and very top shelves.  Has slots on top and bottom of the mount for the mirror inserts.

Main Mount_Bottom Has no slot on the bottom for the mirrors to slide into. (can be just flipped upside down for the top shelf as well)

Main Mount_Top Has no slot on the top for the mirrors to slide into.  (can be just flipped upside down for the bottom shelf as well)

Mid LED Support is used with the same VHB tape, but is meant to go in between LED Modules.  This is a just in case file, in case the glue fails on the strip.  No need to print this unless needed.

Mounting Jig I used this for the 5" spacing needed for the mirrors that slide in.  You don't need to print this, its another very specific tool for my need, but I included it just in case.

Nail Mount for Wire Hider These are little pieces that mount in front of the mirrors, in between the shelves.  They are used to hold the “Wire Hider” in place.  I used tiny nails from Ace Hardware to mount to the wood, installed the “Wire Hider” and then just cut off a piece of the same color of filament to put through the opposing hole. I included a photo for reference below:
 

Screw Hider_Slide On Cover Optional, but can be used to hide the screws even more.  It will just slide over the “Mounts”.

Side Glass Rest Use this to set the glass on top of, if you don't want to use the mounts where the glass slides into them. I did not use this is my spice rack. (Wire Hiders, etc, are not compatible with this)

Wire Concealer Used to in conjunction with “LED Hider_Right” & “LED Hider_Left”. Once you install the LED Hider, you can use this to slide over the wires for a more seamless look. Cut to length with a pair of scissors as needed.  I included a photo for reference below:
 

Wire Hider Use this to hide the JST wires from the LED strips.  This is paired with the “Nail Mount for Wire Hider” Also, this is where the same color filament is cut from off the roll to mount it in place.