1 / 5
Parametric Out of Marbles Bucket Tower Suspension Shelf — image 1
1 / 5

Parametric Out of Marbles Bucket Tower Suspension Shelf

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Unique and minimalist suspension shelf primarily intended for mounting an Out of Marbles Bucket Tower to a wall.

Rating
0 / 5
Likes
2
Downloads
14
Makes
0
Views
150
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike
Motivation

I printed and assembled a seven module Out of Marbles Bucket Tower years ago and we occasionally enjoyed playing with it, but it always seemed to be in the way when sitting on my desktop. It would constantly get jostled and never seemed to be accessible for optimal viewing and tinkering.

Solution

Design and print a custom shelf mount to display the Out of Marbles Bucket Tower that achieves the following objectives:

  • Securely mount a tower of any height to a vertical surface
  • Fully parametric providing customization of all dimensions
  • Ability to make small adjustments to laterally (side-to-side) plumb the tower (assumes the vertical surface is already plumb)
  • Minimal geometry to not distract from the tower’s design and reduce space required on the mounting surface
  • (Optional) Honeycomb cutouts to minimize required filament while maintaining strength in the orientation of the forces (i.e. vertical).
  • (Optional) Front corner border geometry to restrain the base from sliding forward
Customization
  • The Fusion file is included. You can customize most of the parameters (DESIGN | SOLID | MODIFY | Change Parameters) like printer tolerances and mounting screws diameters to suit your needs. The most common parameters you should need are Favorited. The non-favorited parameters should work as well but may require more tinkering to repair broken downstream features.
  • I used the Out of Marbles mesh files in the design process, but deleted them from the shared Fusion file since they're not mine to share. That's why you'll see errors for missing geometry in the Rear Brace Anchor component.
  • The honeycomb cutout features are available as a selection set if you would like to suppress them to create a solid shelf.
Materials
  • Suspension cable – some type of high tensile strength filament (e.g. string, wire, etc.). I used fishing line.
  • Printed parts
    • (1) Shelf
    • (2) Support Tabs
    • (2*) Suspension Anchors
  • Hardware
    • (Optional) (4) Drywall anchors
    • (2*) If not using the printed Suspension Anchors, alternative hardware pieces (e.g. eyelet hooks, etc.) are required.
Printing

See the attached .3mf for my settings and model orientation (supports not required). I printed in PETG on a Prusa MK4S.

Post-Processing

Make sure the support tabs fit snug in the shelf and clean out the mounting slots as necessary.

Installation

Measure with as much precision as possible (e.g. laser level). All measurements are straight from Fusion…of course round as necessary.

     1. Mount the support tabs

          a. Measure, mark, and (optionally) pre-drill the support tabs’ hole centers. The following measurements are what I used and will work if you just print the model without adjusting the shelf slot spacing:

               (Lateral) Holes center-to-center – 152.43 mm
               (Vertical) Shelf top to hole centers – 12.25 mm

          b. (Drywall only) Install the wall anchors
          c. Mount the support tabs ensuring the tabs are straight up

     2. Slide the shelf completely over the support tabs

     3. Mount the suspension anchors. The top end of the suspension cables can be mounted anywhere and in any way that provides the necessary tension to each of the front corners of the shelf. If using the suspension anchors:

          a. Measure, mark, and (optionally) pre-drill the suspension anchors’ hole centers. If mounting as I did, the holes should be 200.5 mm center-to-center to provide a 5 mm gap between the side of the tower and the suspension anchor
          b. (Drywall only) Install the wall anchors
          c. Mount the suspension anchors or your alternative suspension support hardware

     4. Securely tie a suspension cable to each shelf corner

     5. Place the tower on the shelf while supporting its weight

     6. Securely tie the suspension cable to each suspension anchor/hardware

     7. Check for plumb and level adjusting the suspension cables’ tension as necessary.

     8. For additional security, with the tower in the exact right placement, you can use optional rear brace anchor(s) as a template to mark a hole center to secure the rear brace of one (or more) of the tower sections. Once marked, remove the tower and (optionally) pre‑drill then install the wall anchors for the desired rear brace anchor(s), then reinstall the tower and install the rear brace anchor(s).

Questions

Please let me know if you have any questions (Messenger | Printables.com).

Shameless Plug

If this model helped you solve a problem, save some time, or in any way made your life a little easier then please consider clicking the Like button and posting your Makes! If it fell short after clicking on the title of the model, please let me know (Messenger | Printables.com). Either way, Thank you!

Tags