1 / 9
Celebrations Tub Spool Holder (and dehumidifier) — image 1
1 / 9

Celebrations Tub Spool Holder (and dehumidifier)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Two stacked christmas chocolate tubs, bottom one holds silica gel, top one holds a roller base for the filament spool

Rating
0 / 5
Likes
2
Downloads
5
Makes
0
Views
77
Reviews
0

Updated at source:

Model information

Category
Accessories
License
Creative Commons — Attribution

 I am waiting for someone to upload their model so I can correctly reference this as a Remix 

So I had a couple of Celebration's christmas chocolate tubs, one of the older, taller ones (that can hold a spool) and one of the shorter newer ones (that can hold the silica gel).

The Celebrations Tub Spool Holder is not my idea, totally and shamelessly robbed off someone and I'll keep pestering them till they upload it so I can credit them.

Aaaaanyway, this ‘model’ is a collection of bits, it's the marble bearing race, a connector for two PTFE adapters so it can be connected to an existing PTFE tube and a adapter that sits on the outside of the top tub for a PTFE adapter.

Also here is the Freecad source file used for it all. It's parametised in the Spreadsheet in there, so you should be able to make it fit whatever tubs you can find. 

What will you need?

  1. Two tubs, one for the filament and one for the dehumidifying silica gel
    I used Celebrations tubs for this, because I had them
     
  2. PTFE tube and connectors
    I have a Prusa Mini+ which has some PTFE hanging out of it to feed filament into so I connect to that existing tube with another tube, so for this I need 3 adapters, if you are sending the PTFE straight to the printers extruder, then you might only need 1… but having easy access halfway down the line is really handy (I'll explain later)
     
  3. Silica Gel
    I got some of that fancy colour indicating Silica Gel, it starts orange and changes to green as it gets saturated. It can be heated (oven or microwave) to drive the moisture back out again, so it can be reused!
     
  4. Marbles
    Cannot remember how many I used maybe 50? I'll count them when I do the photo's and if you're lucky I'll remember to update this then.
     
  5. Superglue/Crazy Glue (Cyanoacrylate glue)
    To glue the bearing race together
     
  6. Paper Tape (white/blue or otherwise)
    Just makes holding the bearing race together while you glue it so much simpler
     
  7. Two Part Epoxy Glue
    The Filament Port is a proper PITA, you are going to want something stronger than superglue
     
  8. Drill / Dremel / Files / Craft Knife / Sandpaper
    The hole for the Filament Port needs to be big enough that the filament clears nicely all the time, but small enough that the Filament Port doesn't just fall into the tub.
    I sanded the bearing race a fair amount to make sure the joins between each section were smooth and that the general race itself would be as efficient as possible.. Probably didn't need to :)
     
  9. Plastic Tape
    This is just to seal the lid and the join between the tubs, it's not permanent, just enough to stop any more moisture getting in.
     
  10. Double Sided Tape
    Holds the ring in place in the tub, I also used the spare lid to create a wider rim so all sorts of shapes and sizes of filament spools would sit on the top of the bearing race, and I held that onto the top race with double sided tape
     

Building It 


First of all, if you haven't installed Freecad, do that, cos if you need to change any of the sizes you're gonna need to do that.

This is the list of the dimensions I needed in the model:

NameSize (mm)
marble_dia17
wall_depth1
tub_base_dia170
tub_port_dia215
ptfe_coupling_dia10
filament_dia2
ptfe_coupling_thread_dia5
ptfe_coupling_thread_depth5

So, measure a average marbles diameter, is it 17mm?
Is the base of your tub 170mm?
Where you plan to put the Filament Port, the diameter at that point, is it 215mm?
The PTFE couplings you have, are their diameters 10mm?
The thread diameter of them is 5mm?
The depth of that threaded part of them is 5mm?
If any of them are not, you'll need to edit that value in the Freecad source file, in the spreadsheet and export the affected parts.

Ok, really building it now

Print 16 of the marble_bearing_half-quarter objects.
Print 1 of the filament_port object.
If you want to make a coupling on the PTFE tube to connect to another PTFE tube then also print 1 of the ptfe_coupler_coupling object.
 

That was just printing… now can we build things?

Filament Tub

Ok, grab 8 of the marble race parts and put one ring together using paper tape.
Now grab the other 8 and paper tape them together.
You should now have both halves of the race so throw in enough marbles to check how it's going to work.
Spend a while just being amazed that marbles can be used as bearings… Show someone else, they may or may not be astounded.

If you are a bit careful you can keep the paper tape on just the bottom to act as a hinge, then fold the ring in half, put glue on the exposed gap, fold the ring back together again and in the few scant seconds you have before the super glue does what super glue does, try to align them as exactly as you can. Rinse and repeat till you have glued up both ring sections.

Find the centre of the tub… (mine was staggeringly obvious), measure out a circle from it to match the outer or inner diameter of the bearing race, apply some double sided tape to one of the races and stick it on down there, now. 

This bit's optional, I wanted a wider ‘shelf’ to sit the filament spool on because I've seen lots of different shaped spools so I had a spare lid from making this, so used that to create a ‘O’ shape to sit on the top of the bearing race (the hole in the centre of it to allow the air to pass through for the dehumidifier), so that is then stuck onto the top race with double sided tape.

Drill as fancy a pattern of holes in the bottom of the filament holding tub as you like.

Halfway up the tubs side, drill a hole for the Filament Port, offer it up to make sure you are happy with the direction the port will point (aka ‘sir shall dress’) and then start whittling out a very long and thin oval until it matches with the Filament Port, then glue it in place with Two Part Epoxy. I used paper tape to hold it where it needed to be while the glue cures.

When it's completely cured then fit the PTFE tube into the Filament Port.
If like me you want to have a coupler between this and the printer (makes changing filaments super easy) then make up the coupler and fit that onto another piece of PTFE tube and connect that.

Dehumidifier Tub

This ones easy, try and put the Filament Tub in the Dehumidifier Tub and the Filament Port gets in the way, so just cut down the height of the Dehumidifier Tub to be under the Filament Tub when it's in there. Be careful testing cos if your tub doesn't  have little wings that stand out of the sides of the inside of the tub (mine does) then you're gonna lose that nicely glued Filament Port. If it doesn't have those wings, just put something in the bottom Dehumidifier Tub to make sure the Filament Tub on top can't go too far down.

 

Ok, that's it, put some Silica Gel in the bottom, put your Filament in the top, thread the filament through the Filament Port, through the optional Coupler and into your printer, and if this is being painful, just remove the PTFE tube from its coupler (push the blue ring in) and thread it through, then when it's threaded through push the  PTFE back onto the coupler.

Finally, and you can likely ignore this, put some plastic tape around the seams between the tubs and on the lid to stop moist air wandering in.

..that's really it now. 

 

 

Tags