1 / 4
Instant Film Borders for Lithophanes (Instax, Polaroid, and Type 100) — image 1
1 / 4

Instant Film Borders for Lithophanes (Instax, Polaroid, and Type 100)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This pack contains borders that you can use to create lithophanes that look like instant film photos.

Rating
0 / 5
Likes
3
Downloads
16
Makes
0
Views
118
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution

Instant Film Borders

 

*Edited models for more precise dimensions Feb. 20, 2025 

    

 What's In this Pack?

Fujifilm Instax
  • mini
  • SQUARE
  • WIDE
Polaroid
  • 600/i-Type/SX-70
  • Go
Type 100 Film
  • Type 100

 

     How to Use.

You will need to generate a lithophane image and then in your favorite slicer or 3D model software you will place the lithophane inside the border and combine or “Join” them together as a single printable lithophane.

 

     Sizes.

When you are making your image lithophane use the “Image” sizes below.

Fujifilm Instax mini
  • Border - 54mm x 86mm
  • Image - 46mm x 62mm
Fujifilm Instax SQUARE
  • Border - 72mm x 86mm
  • Image - 62mm x 62mm
Fujifilm Instax WIDE
  • Border - 108mm x 86mm
  • Image - 99mm x 62mm
Polaroid 600/i-Type/SX-70
  • Border - 88mm x 107mm
  • Image - 79mm x 79mm
Polaroid Go
  • Border - 53.9mm x 66.6mm
  • Image - 46mm x 47mm
Type 100 Film
  • Border - 107.95mm x 82.55mm
  • Image - 95.25mm x 73.15mm

 

     Aspect Ratios.

When you are cropping the image that you are going to use, please refer to the aspect ratios below.

Fujifilm Instax mini
  • 1:1.348
Fujifilm Instax SQUARE
  • 1:1
Fujifilm Instax WIDE
  • 1.6:1
Polaroid 600/i-Type/SX-70
  • 1:1
Polaroid Go
  • 1:1
Type 100 Film
  • 1.31:1

 

     Print Settings.

Everyone seems to have their own way of printing lithophanes, so these are the settings that I personally use. To start lithophanes should be printed standing up along the Y-axis with the exception of some types of color lithophanes that need to be printed flat. (Follow the instructions of whatever site you are using.)

     Slicer Settings.

Nozzle
  • 0.2mm
Initial Layer Height
  • 0.16mm-0.2mm
Layer Height
  • 0.04mm-0.08mm
  • Note: Smaller layer heights can result in better image quality.
Walls
  • 9999
  • Note: Yes, you want it to be all walls.
Infill
  • 100%
Speed
  • 25-100mm/s
  • Note: Slower is better. You want to get as much detail as possible. Printing too fast can cause image defects. I personally don't care how long it takes if the image turns out stunning.
Brim
  • 10mm Outside

     Lithophane Image Settings.

Maximum Thickness
  • 3mm
  • Note: You will want the border that you use from this pack to be the same height as this number. That means when laying flat the Z Value of your lithophane peaks and border should be this number.
Minimum Thickness
  • 0.6mm
Lithophane Resolution (mm/pixel)
  • 0.04mm-0.1mm
  • Note: Adjusting this number can make the file size of your lithophane image VERY large. Just keep in mind that the smaller the number is the better the picture will look while trying to balance the file size. If your file size is too large it will crash your slicer.

Lithophane Dimensions

  • See the Sizes section above

 

 

 

 

 

 

     

 

 

 

 

 

Tags