Mountain Bike MTB Fork Steer Tube Galaxy SmartTag2 Holder (Fox34)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Galaxy SmartTag2 holder that fits into the fork steer tube, designed for my Fox 34 fork
- Rating
- 0 / 5
- Likes
- 14
- Downloads
- 41
- Makes
- 0
- Views
- 523
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Outdoor Sports
- License
- Creative Commons — Attribution — Noncommercial — NoDerivatives
This is a holder for the Samsung Galaxy SmartTag2 to fit into the steer tube of a standard bike fork. Designed for my Fox 34 fork, which has a max internal diameter at the edge of 34mm with internal tapering.
The “Door” holds the SmartTag2 in place inside the holder to prevent it from rattling around inside, allowing for the SmartTag2 to have a loose fit so it can be easily removed from the print.
Its designed with 3 printable O-rings to allow it to stay in while having some sort of decent seal inside since the tube is smooth.
(Designed with) Fork: FOX 2021 RHYTHM 34 FLOAT 29 140
Fork Inner Diameter: 34mm
Now, there are two versions of this model, one titled “Removable Ver” (v1) and the other “Permanent Ver” (v2). This is quite important as they differ slightly, the v1 is designed to fit into the tube with the possibility to be removed as shown in the below video.
The v2 has larger O-rings so it has a very tight fit inside the steer tube meaning that it has to be pushed out from the other side (top) of the fork. As seen in one of the pictures, the top part of the v2 broke off making it (almost) impossible to remove when testing.
Edit to v2: No longer has the top “lip” making it basically impossible to remove without pushing it out from the other side.
The video shows how to assemble the v1 removable model, insert it and remove it from the steer tube (I was using a prototype at the time but the final doesnt differ too much)
Caution: with the v1 removable model, be careful when prying it out to avoid accidentally breaking the top part
Note: each file should contain all parts necessary for the print, do not mix parts between the versions as dimensions and tolerances vary
- Print in orientations as seen in first picture
- Recommended to print MainBody in black or a matching colour to your fork
v1 removable ver print settings:
v1 MainBody:
- Material: PLA
- Layer Height: 0.15 - 0.2mm
- Infill: 15 - 30% Gyroid
- Supports: Recommended
- Brim: Not needed
v1 Door:
- Material: TPU (around 92A)
- Layer Height: 0.15mm
- Infill: 50% Gyroid
- Supports: On/ Everywhere
- Brim: Not needed
v1 O-rings:
- Material: TPU (around 92A)
- Layer Height: 0.15mm
- Infill: Doesnt matter as they will be solid either way
- Supports: NOT RECOMMENDED
- Brim: NOT RECOMMENDED
v2 permanent ver print settings:
v2 MainBody:
- Material: PLA
- Layer Height: 0.15 - 0.2mm
- Infill: 20 - 50% Gyroid
- Supports: Recommended
- Brim: Not needed
v2 Door:
- Material: TPU (around 92A)
- Layer Height: 0.15mm
- Infill: 50% Gyroid
- Supports: On/ Everywhere
- Brim: Not needed
v2 O-rings:
- Material: TPU (around 92A)
- Layer Height: 0.15mm
- Infill: Doesnt matter as they will be solid either way
- Supports: NOT RECOMMENDED
- Brim: NOT RECOMMENDED
If you have any questions or requests for this model, feel free to comment!
Any feedback is highly appreciated.
Enjoy :)