1 / 1
eGolf J1722 Connector Reinforcement or repair for broken plastic tabs — image 1

eGolf J1722 Connector Reinforcement or repair for broken plastic tabs

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

eGolf J1772+CCS charge port tab reinforcement for busted or broken tabs

Rating
0 / 5
Likes
4
Downloads
20
Makes
0
Views
243
Reviews
0

Updated at source:

Model information

Category
Automotive
License
Creative Commons — Attribution — Noncommercial — Share Alike

eGolf have notoriously weak J1772 connector and break at the tabs.  Mine were broken and I planned on the fix, and it would need some reinforcement. Below is the final result.  A couple corners needed hacksawing to avoid interference with other parts.

This fix involves gluing the original tabs back on (if you have them) and then adding the printed part.   If your tabs are not broken, the parts can be added quickly.

The parts here reinforce the connector in x-y-z while not interfering with the J1772 or CCS connection.  I printed the “standard fit” parts and the right was snug, the left had a gap.  The “tightfit” version was created that moves the top over 2mm inward and closed a gap.   No glue was used for the install of the 3d printed parts.

 
Design

The part surrounds the part from a clock perspective, 7pm-11pm on left, 1-5pm on the right.  This avoids a wire on the bottom and an area at the top where space is lacking.  The part has a 1mm high ridge that sits in a gap around the connector.  This is what holds it in place from “sinking in” if the tabs were to break.

 

Supplies
  • Glue: ABS Pipe cement (black, in the plumbing section), or JB Weld plastic epoxy.  Superglue might work also, I did not test it.
  • hex wrench for screws, a T-handle was perfect
  • 8"/20cm tweezers for holding screws (unless want to open the wheel well)
  • good lighting
  • a tray to hold all the bits and bobs for this.
Planning

During the glue-up, the charge port should not be used as your work can break even if the glue is cured.  If you car can go uncharged during repair, that is ideal.  The glued tabs are not as strong as original.  Depending on the glue used, glue can take a few hours to set, or if use epoxy repairs could go faster.  For my car, the first tab was glued and left to cure several hours before it was screwed in and the second tab was glued+screwed in for curing.  Then the other two tabs were glued+screwed and left overnight to cure.

Gluing Tabs

Clean the busted tab surfaces with acetone and put glue on both surfaces.  If you can put on the tabs and screw together, the screws can help hold alignment.   This goes easier if one tab is already cured as it can hold alignment for the other three.  

Glue the tabs back on with ABS Pipe cement (black, in the plumbing section).  JB Weld also worked on one tab, but the ABS glue was the best IMO.    This was solid enough after a few hours the car was able to get plugged in and not break the tabs.    I was nervous unplugging the next day, however I needed to  charge so the risk was necessary.  If you can, avoid charging until the repair is complete.

 
Printing

0.4mm nozzle, PETG, 5 layer shell, 50% infill.   Use the mirror function to create the rigtht side.  Parts take 70mins each on a mk3.5

Installing

If parts are dropped they can be fetched by removing the wheel well cover.  My chargeport  some of the rubber surround was cut due to being stranded at a charger with a sunk port.

  1. The tabs are glued on and thus the port is aligned and ready for the 3d printed parts.
  2. Remove the screws on one side. left or right.
  3. Put part in place and install first screw.  If the screw gets dropped, this is where having the wheel well cover open helps for retrieval. 
  4. Reinstall the second screw.  Mine were 17mm, long enough to engage all threads.
  5. If upon tighening the printed part “twists away” from being snug with the connector, that ridge is “passing” the gap in the connector.  A washer is needed between printed part and tab until the righten part has a minimal gap.  Being the ridge is only 1mm deep, any noticeable gap is detrimental.  Optionally you could fill that gap with ABS glue if you are ok with the semi-permanence of glue.
  6. Repeat for the other side.
  7. Both sides should have good contact against the connector, capturing it via the gap. 

Tags