Čmeláčí klapka na čmelín / Bumblebee Hive Flap
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
99% printable bumblebee hive flap for yours bumblebees safety against parasites.
- Rating
- 0 / 5
- Likes
- 15
- Downloads
- 128
- Makes
- 1
- Views
- 490
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Outdoor & Garden
- License
- GNU General Public License v3.0
Czech version - English follows.
🐝 Čmeláčí Klapka na Úl
(inspirováno CmelaciPlus)
📦 Popis
Tato 3D tištěná ochranná klapka chrání čmeláčí úl před parazity a predátory. Obsahuje volně pohyblivá dvířka, která se otevřou, když čmelák zatlačí. Pomocný texturovaný pás pomáhá čmelákům klapku nadzvednout.
Pro správnou funkci instalujte klapku ještě před příchodem královny, udržujte ji čistou a dbejte na to, aby byl úl vodorovně. Pravidelná údržba (kontrola šroubků apod.) prodlouží životnost a zajistí spolehlivou ochranu.
🖨 Nastavení tisku
Materiál: PETG nebo ABS (odolné vůči UV a slunci)
Barva: Světlá – rozhodně ne černá! (čmeláky by to mátlo)
Výška vrstvy: 0,2 mm (nebo větší)
Výplň: 10 %, libovolný vzor
Podpěry: NE! 🙂
Orientace dílů: Nejsou třeba otáčet - jsou již připraveny správnou orientací.
🧩 Díly
Tělo
Klapka
Stříška
Lezící plocha (tiskněte z tmavého materiálu, ideálně černého)
🛠 Montáž
Na klapku přilepte kousek tvrdé fólie (např. z pytlíku od filamentu). Fólii umístěte do vyznačeného prohloubení a přilepte ji vteřinovým lepidlem.
Připevněte klapku k tělu pomocí dvou šroubků M3×20 (mohou být i trochu kratší/delší).
Připevněte stříšku dvěma šroubky M3×8 nebo M3×10.
Vložte lezící plochu do vyznačeného otvoru.
⚠ Dbejte, aby se klapka mohla úplně zavřít! Pokud překáží, lze ji zbrousit nebo upravit. Pokud klapka sedí rovně, můžete plochu přilepit. To ale až úplně nakonec!
📝 Poznámky
Potřebujete šroubovák/imbus (dle typu šroubů), vteřinové lepidlo a kousek fólie.
Dotazy? Napište do komentářů 😊
English version
🐝 Bumblebee Hive Flap
(inspired by CmelaciPlus)
📦 Description
This 3D-printed protective flap is designed to guard bumblebee nests from parasites and predators. It features a freely moving gate that opens when bees push against it, along with a textured climbing strip to help them lift it.
For best results, install the flap before the queen arrives, keep it clean, and make sure the hive is level. Regular maintenance (e.g. checking screws) will extend the lifespan and effectiveness.
🖨 Print Settings
Material: PETG or ABS (UV/sun-resistant)
Color: Any light color (do not use black – it may confuse the bees)
Layer Height: 0.2 mm (or higher)
Infill: 10%, any pattern
Supports: NO! 🙂
Orientation: All parts are pre-oriented correctly
🧩 Parts
Body
Flap
Roof
Climbing surface (print this in dark/black material)
🛠 Assembly Instructions
Glue a straight piece of stiff foil (e.g. cut from a filament bag) into the flap’s small indent. Superglue works well.
Screw the flap to the body using two M3×20 screws (a little shorter or longer is fine).
Screw the roof to the body using two M3×8 or M3×10 screws.
Align the climbing surface in its slot.
⚠ Ensure the flap can fully close! If it doesn't, sand or trim the climbing surface. Once the flap sits flat, you can glue it in place – but do this last! Gluing too early may block movement.
📝 Notes
You'll need a screwdriver or Allen key (depending on screws), superglue, and a small piece of foil.
Questions? Feel free to ask in the comments 😊