1 / 12
Minisforum MS-A1 Noctua NH-L9a Case — image 1
1 / 12

Minisforum MS-A1 Noctua NH-L9a Case

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A case to fit the Noctua NH-L9a cooler on the Minisforum MS-A1 motherboard

Rating
5 / 5
Likes
41
Downloads
243
Makes
1
Views
3,200
Reviews
1

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution — Noncommercial — Share Alike

The Minisforum MS-A1 is an awesome low power motherboard case combo, but the cooler is weak and kind of noisy. The cooler mount is almost but not quite AM-5 cooler compatible. I made a mount to adapt the NH-L9a to the slightly smaller mounting pattern on the MS-A1 motherboard, available in my profile. This design provides a case to fit this motherboard and cooler combination.

⚙ Required Parts

  • Minisforum MS-A1 with Noctua NH-L9a cooler installed

  • 4x M3x8mm button head screws

  • 4x M3 nuts

  • 80mm fan grill (optional)

✏ Printing Guide

General Settings
  • In my testing with my 8700G CPU, PLA works fine although if you are running a much more powerful CPU, you may want to consider ABS, ASA or PETG for better heat resistance. I used Matte black Polymaker PolyTerra PLA.

  • For the outer shell, front and rear panels, I have provided vent cut-outs in the 3MF file. This is designed to be used either as a negative part modifier to create a hole (in which case you can add a separate mesh after the print) or as a modifier to allow you to turn that area of the part into a mesh using infill. Directions are provided in the appendix at the bottom.

  • I recommend a 0.4mm nozzle. A 0.6mm may work ok but there are a couple of tight sections where a 0.6mm nozzle might produce less than perfect results.

  • I used 0.28mm layers with 2 walls, but most settings will work fine.

  • This model requires precision printing. I highly recommend to use your the slicer's shrinkage compensation. Tune this well for the filament you plan to use. I found my filament shrank by 0.3% so I used 99.7% shrinkage (XY) in my filament settings.

Outer Shell
 
  • Print the outer shell standing up on its end with the fan cutout towards the TOP. Use a 10mm inner and outer brim to prevent warping.

  • I recommend using Inner/Outer/Inner wall printing order and a fixed clockwise or counter-clockwise wall loop direction to make the outer shell extrusion as consistent as possible.

  • Suggested vent mesh modifiers:

    • Wall Loops: 0

    • Sparse infill: 20% gyroid (try different settings, have fun)

  • Use tree support to support the fan cut-out. I used auto tree supports with the following settings:

    • Threshold: 40 degrees

    • Support blockers to all of the screw holes as they aren't necessary to support.

    • Branch Diameter Angle: 7 degrees

    • First Layer Expansion: 5mm

Front Panel
  • Print facing down

  • Suggested vent mesh modifiers:

    • Wall Loops: 2

    • Top Shell layers: 0

    • Bottom Shell layers: 0

    • Sparse infill: 35% gyroid (try different settings, have fun)

Rear Panel
  • Print facing UP

  • Support: Normal (auto), snug

  • Suggested vent mesh modifiers:

    • Wall Loops: 2

    • Top Shell layers: 0

    • Bottom Shell layers: 0

    • Sparse infill: 20% honeycomb (try different settings, have fun)

Button

Print with the back (the flat part) of the button on the bed. The top of the print will be the front of the button - so I recommend using your slicer to iron the surface for a nice finish.

Button Light Pipe

Print with the back (the widest part) on the bed. Print out of a translucent material. I used translucent PETG. The top of the button will face the front, so I recommend using your slicer to iron the top surface for a nice finish.

Feet

Print four of these out of TPU. I used Ninjaflex.

👷 Assembly Instructions

  1. Print out the parts. See the printing guide above for guidelines.

  2. Press the button light pipe into the button from the back.

  3. Attach the button to the front panel. I provided holes on the front panel to let you glue a short length of raw filament in, then you can slide the flexture tabs over the filament, trim the filament down to 2mm or so and then melt the end of it with a soldering iron to secure the flextures in place. Alternatively you can just glue the flexture tabs in place with or without any filament. Make sure to only glue the circular part of the flextures - the arms should remain free to flex.

  4. Glue the fan grill into the provided indentations in the roof of the outer case from the inside. Or if you are glue-adverse like me, you can just sit it in there and perform final assembly upside-down. The cooler will press the grill into the roof indents and keep it in place.

  5. Pop M3 nuts into the holes inside the outer casing and screw in the M3x8 screws all the way to until they are tight to pull the nuts fully into position. Then unscrew the screws, add the feet, and screw them back in. Make sure none of the screws are protrude above the nuts, otherwise they will interfere with the motherboard.

  6. Slide the motherboard into the case from the back.

  7. Pop the rear panel into place

  8. Pop the front panel into place (gently, don't break the clips)

  9. Optionally, use the countersunk screw holes on the bottom to secure the case in place. The original screws from the Minisforum case work for this.

  10. Enjoy!

🪟 How to use the Vent modifiers

This is specifically for Orca Slicer but similar steps should work for Prusa Slicer and Super Slicer.

  1. Import the 3MF file and if the slicer asks if you want to import as an object with multiple parts, click YES

  2. Configure the global slicer settings appropriately for the main part, then click into the objects view, find the vent objects by clicking on each one and seeing which one is selected in the preview, and change the vent modifier object types to modifiers. Do this by right clicking on the object, and click “change type”, then select “Modifier”.

  3. Staying in the “Objects” pane, set the modifier slicer settings appropriately to adjust the wall loops, top / bottom layers and sparse infill as desired to cause the modifiers to generate mesh panels where the vents should go.

Tags