"LSD" Sovol SV06 dual Y-axis stepper motor modification
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Sovol SV06 dual Y-axis stepper motor and 9mm belt conversion
- Rating
- 0 / 5
- Likes
- 4
- Downloads
- 17
- Makes
- 0
- Views
- 374
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- GNU General Public License v3.0
CoreXY printers with dual A&B motors have taken the “AWD” nomenclature. This is only for a single axis, so I think the name “LSD" (like a traction-enhancing limited -slip differential in a car) works here.
Warnings:
- The order of operations for assembly is very specific and I do not remember it in detail. I had to put things together, partially disassemble, and try a different order several times. This modification is not for the impatient. Do not attempt this on your only 3D printer.
- I highly recommend parts printed with ABS, ASA or other filament capable of enduring high temperatures. You will probably need some kind of enclosed printer.
- This was only tested on a printer running Klipper on a non-stock motherboard with additional stepper motor drivers.
- The two stepper motors must be synchronized after setting the belt tension. I will not describe that process here, but I will advise that if your stepper motor in the rear position has indentations for the grub screw, go ahead and set the grub screw against the indentation on the front stepper motor, but DO NOT set the grub screw against the indentation on the rear stepper motor. The rear stepper motor pulley must be able to move a little bit. There is a notch in the rear stepper motor mount that makes access to the grub screws on the pulley pretty easy.
- You will need to modify your Klipper configuration to make this work. I will not describe those modifications here, but they are similar to those needed when adding an additional stepper motor driver for independent dual z control.
Why do this?
I wanted to increase the performance of the y-axis to match that of the x-axis. With the stock motion system my resonance testing results suggested a recommended maximum acceleration of ~10500 mm/s^2 for the x-axis and less than 4500 mm/s^2 on the y-axis. After adding the second stepper motor the recommended maximum acceleration of the y-axis more than doubled to 9000 mm/s^2.
* I also braced the SV06's rather wobbly frame with two lengths of 2020 extrusion parallel to the y-axis. Thes extrusions connected the front and rear aluminum plates via M4 screws and holes drilled in the front and rear plates. The new 2020 extrusions were also connected to the existing 2040 extrusions via printed brackets. Find the parts for that here.
You may or may not be able to piggyback the second stepper motor off the stepper driver for the existing y-axis motor; I did not try it that way. My printer has a non-stock motherboard with extra stepper driver slots for the second y-axis stepper motor driver.
Sensorless homing still works on the y-axis after adding the second stepper motor driver. You probably should test and readjust the driver_sgthrs value for the stepper_y after performing this modification.
The initial idea was to make a simple model to replace the front tension with a stepper motor, but the project snowballed quickly. The front (tensioning) stepper motor bracket moves fore and aft on a pair of sliding dovetails. Tension is adjusted with a pair of M4 screws and the stepper motor's position is locked via seven M3 screws in oblong holes. The tensioning stepper motor mount is a dual-shear design.
The move to a 9mm belt also requires replacing the existing stepper motor and its mount. The replacement mount is a dual-shear design better suited to the higher belt tension of the wider belt.
The 9mm GT2 belt means the belt interface must be replaced. The new belt interface is made of several parts and allows full travel on the y-axis.
All printed parts operate in close proximity to the heated bed, warm stepper motors, or both. I suggest printing all parts in ABS with a minimum of four walls, four top and bottom layers, and 20% infilll. I did my best during the design process to minimize overhangs, but you will need to enable supports for some parts. I suggest organic supports and checking the “on build plate only” option in your slicer. Some parts have counterbores with design supports integrated into the model. You will just need to poke a tool through the hole to pop out the design support after printing.
The bracket that connects the bed to one of the rod bearings of the y-axis must also be replaced in order to maintain full travel on the y-axis.
You will need a bunch of parts:
- Two stepper motors with 24mm (or longer) output shafts. The stock units are 34mm. but a pair of 40mm stepper motors will fit. I can't remember, but I don't think the stock y-axis stepper motor has a long enough output shaft to be used in this modification.
- two F695 bearings
- two 20T pulleys for 9mm GT2 timing belt to fit 5mm output shaft of stepper motors
- some 9mm GT2 belt
- a bunch of M3 and M4 screws of varying lengths. I can't remember what screws came with the printer and which ones are new.
- around twelve M3 threaded inserts
- approximately eight M4 threaded inserts
- some M4 nuts
- additional wiring for a second y-axis stepper motor
You will need to remove the front plastic panel. You will also need to drill two holes in the front aluminum panel for the M4 screws used to adjust belt tension. I designed a part that bolts to the aluminum panel and provided a pair of holes that can be used with a spring-loaded punch to mark the location of the holes. You could probably also use it as a guide to drill the holes.
This design was inspired by brain-no-work's existing designs to accomplish similar goals. He also gave me the idea to add the new 2020 extrusions to reinforce the wobbly stock SV06 frame.
Some of the pictures are in-progress shots. This modification is finished. I am now adapting it to fit the SV06 Plus.
