Three-part lithophane of a Flamingo
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Three-part lithophane of a Flamingo in a stained-glass style
- Rating
- 0 / 5
- Likes
- 3
- Downloads
- 30
- Makes
- 0
- Views
- 129
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- 2D Plates & Logos
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
[Commercial license access is now provided for this model at Thangs dot com/designer/tlavedas1]
This is a three-part HueForge Lithophane of a Flamingo in a stained-glass style. The first part has the blues and greens of the foreground with the reds and yellows blanked out. The second part holds the red parts of the bird. In the third part the yellow areas remain for both the yellows and areas to blend with the blues and reds to give greens and oranges, respectively. No green, orange or black filaments are used, though these colors along with others are present in the final result.
Working from the STL files means that the red (part 2) should be mirrored around the Z-axis in the slicer to aid is the assembly of the two parts. When mirrored, the two parts assemble back-to-back (flat side to flat side. The yellow part will need to be mounted with the uneven side against the red part.
Feel free to substitute your filaments, but seek to use ones with similar transmission distance (TD) values. The base layer should be the most transparent white filament you have (TD > 15, suggested), like a natural or transparent. The design assumes PETG for thermal resistance, but PLAs can be used, if the risk of exposure to very strong sunlight is low.
***IMPORTANT NOTE*** All parts have very thin base layers, so special care is needed to remove them from the print bed. It is probably best to cool them completely before trying. A few minutes in a freezer and/or some glue stick as a release agent is wise. I have rushed some parts and regretted my impatience.
When joining the parts be sparing with the adhesive, like a super glue, especially in the lighter parts. The adhesive will change the colors if it is not behind the darker parts. I just used some around the dark parts and around the very edge to keep the glue from showing. If spread thin and uniformly, it should not show too much.
Part 1: Blue
Project: Flamingo_Blue.hfp
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm
The Model is 150x153.08mm in size
You may print at higher layer heights below the Base Thickness of 0.32mm
The Max allowed Thickness is 1.04mm and the Actual Thickness is 0.88mm
Filaments Used:
PETG GeeeTech Transparent Transmission Distance: 100
PETG PolyLite PolyMaker Teal Transmission Distance: 1
PETG Kaaber Blue Transmission Distance: 3.3
This print uses 3 unique filaments
Swap Instructions:
Start with Transparent
At layer #4 (0.4mm) swap to PolyMaker Teal
At layer #6 (0.56mm) swap to Blue for the rest.
Part 2: Red (NOTE: Mirror this part around the X-axis in the slicer for easier assembly)
Project: Flamingo_Red.hfp
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm
The Model is 150x153.08mm in size
You may print at higher layer heights below the Base Thickness of 0.32mm
The Max allowed Thickness is 1.04mm and the Actual Thickness is 0.88mm
Filaments Used:
PETG GeeeTech Transparent Transmission Distance: 1e+02
PETG Kaaber Red Transmission Distance: 6.5
This print uses 2 unique filaments
Swap Instructions:
Start with Transparent
At layer #4 (0.4mm) swap to Red for the rest.
Part 3: Yellow
Project: Flamingo_Yellow.hfp
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm
The Model is 150x153.08mm in size
You may print at higher layer heights below the Base Thickness of 0.32mm
The Max allowed Thickness is 1.04mm and the Actual Thickness is 0.72mm
Filaments Used:
PETG GeeeTech Transparent Transmission Distance: 1e+02
PETG Bambu HF Yellow Transmission Distance: 4
This print uses 2 unique filaments
Swap Instructions:
Start with Transparent
At layer #4 (0.4mm) swap to Yellow for the rest.
Because there are so few filaments used per part, it is not unreasonable to assume any FDM printer that is able to pause for a filament swap could be used to make this model. At most it requires two swaps for the blue part.