1 / 3
GridLink Chess, 60mm Squares, FIDE Compliant Chessboard — image 1
1 / 3

GridLink Chess, 60mm Squares, FIDE Compliant Chessboard

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

The largest allowed tournament chessboard in four sections for portability.

Rating
0 / 5
Likes
8
Downloads
19
Makes
0
Views
155
Reviews
0

Updated at source:

Model information

Category
Board Games
License
Creative Commons — Attribution — Noncommercial — Share Alike

This model extends/modifies GridLink to create the largest FIDE compliant chessboard via tight fitting hidden jigsaw-style connections. The result magnetically fastens from four parts for ease of travel. It has the thickness, weight and feel of a permanent set. Border coordinates are available for both monocolor and multicolor capable printers, as well as a simple no-coordinate flat edge border.

The images show versions made on a single color MK4S with printed coordinate inlays affixed with CA glue. Two-color or more printers can simply print the coordinates in place.

To assemble, you will build four nearly identical quarter-chessboards. 2 start with a black corner, 2 with white. And each quarter will need its specific chess coordinates if you choose to use them.

Chess pieces to go with it are here: Chess Set, Traditional Modern

Thanks to Dumitru for suggesting I try magnets instead of barrel hinges, and a lot of other good Chess analysis and conversation.

GridLink is a highly flexible system for creating panels, boards, wall art, etc. More GridLink parts and projects can be found here: https://www.printables.com/search/models?ctx=models&q=GridLink 
 

INSTRUCTIONS: 

The hardest thing about building this is that you cannot fit any piece or set of pieces together if the joining sides have both a socket and a tab (thus step 4 below). So:

  1. Print the common parts and your choice of edges. Top layer and wall quality is key. 4 top layers and 3 wall loops works well for me. 
       - Make sure your Elephant's Foot Compensation is calibrated, or slightly over-done.
       - If ironing works well for you, this may be the time for it. 
       - If printing coordinate inlays, test whether you get the best appearance printing as modeled
         (usually best), or flipped right-side-up. Best results depend on your printer and print bed.
    Test with a couple of squares before printing full batches!
     

  2. Remove all of the print supports in the sockets and center holes.
     

  3. Lay all of the parts for the whole chessboard out on a table.
     

  4. IMPORTANT: Starting with the corner piece (2 tabs and 2 flat sides, build only outward from that corner in complete rows or columns. Long story short, don't make a U-shape, or the connector covers will block you from filling that in to complete your chessboard.
     

  5. As you complete quarters of the chessboard, make sure the coordinates are correct and the inner edge pieces have magnet slots on their outer side. Things should not be too terribly difficult to disassemble and fix at this point.
     

  6. Use a mallet on a hard flat surface to really get the chessboard joints smooth. They can be pressed or pounded to a very flat state.
     

  7. (Optional) Add 2 or more 250mm x 4mm stainless steel rods into the channels on the inside edges of the board quarters. Slots have been cut on the underside of the edge pieces to access (for removal or adjustment) these rods. You may need to tap them through with a hammer, especially if the channel isn't clean after printing. 

    Each rod channel is 290mm long, so you should be able to bury these about 20mm past the inside edge of the quarter-chessboard. Rods will force the squares to remain aligned and sturdy. 
     

  8. (Optional) Add 10mm round magnets under each chess square. It is much easier to do this before you insert the bar magnets into the edges, as those magnets will pull the round ones out of place.
      - Holes are 14mm round with a 2mm chamfer to make removal of supports easier. Thus 10mm round magnets should settle into place and auto-center themselves.
      - Use a magnetic chess piece to make sure the magnet orientation is correct for every square before gluing, and to hold the magnet in place for gluing.
      - Make sure magnets are lying flat and centered. Drop some glue around the edges to hold them in place.
     

  9. With all four quarters of the board put together as if configured for play, place the board upside down. Insert and glue pairs of 20x10x3mm neodymium magnets into each mating pair of magnet slots. Make sure all magnets are correctly oriented, and let the magnets hold the board in place to squeeze any glue flat on the connecting side, mainly filling and holding from the back side.
     

GLUE TIPS:

Cyanoacrylate glue (CA / Super Glue) vapor will react with PLA to form a white stain. Thick CA glue is nonetheless perfect for this use case. You can avoid staining by running a fan across your work area to prevent concentration of CA fumes. Please test this process before getting too deep into it.


BOM: 

‘Likes’, ‘Follows’ and ‘Downloads’ all help to elevate goods designs, like any other social media. If you like a thing, please click ‘like’.

 

REVISIONS: 
   2025-10-30: Initial Release
   2025-11-12: Added borders with smaller coordinated font, aligned next to board, as well as Cornice edges.
   2025-11-14: Converted many files to .3mf format for better on screen thumbnails.
   2025-12-12:
      - Added cover image with much better color choice than garish yellow with blue letters.  :-)
      - Revised description.

Tags