Size-adjusted Parts for the FRAKS Flexarm -Heat Insert Press
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This posting provides some size-adjusted parts for use in the FRAKS Flexarm – Heatset Insert Press by turtlecrawler.
- Rating
- 0 / 5
- Likes
- 7
- Downloads
- 30
- Makes
- 0
- Views
- 201
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Mechanical Parts
- License
- Creative Commons — Attribution — Share Alike
I recently purchased a hardware kit from KB3D.com for building the FRAKS Flexarm Heatset Insert Press. In addition to the hardware, several 3D printed parts are needed to complete the build. The designer of this elegant kit, Turtlecrawler, has kindly posted the required STL and STEP files on printables and on github.
After printing the first round of parts, I found that my printer did not deliver joints and brackets that would fit bearings and the brass bushing. Fortunately, and very kindly, turtlecrawler has provided STEP files for this kit on github so it has been possible to adjust the size of the openings in the joints, base and brackets to achieve better fit. I’m sharing .STL files for size-adjusted parts for use by others who might encounter similar fit issues.
The adjusted parts are as follows:
Joints: the openings in the joint parts for the F695 bearings are increased from 13mm to 13.1mm. The adjusted joint parts also have a 0.4 mm recess on one side so that one bearing can be pushed a bit deeper into the joint part. This adjustment decreases the distance between the bearings so that the arms more easily slip into the front, center and rear brackets.
Rear bracket: The size of the hole in the bottom rear bracket is increased from 14.2mm to 14.35mm more easily accommodate fit of the brass bushing.
Front bracket and TS101 Mount: Try as I might, I could not get the dovetail in any of the size-adjusted TS101 mounts to easily slide into the dovetail groove in the front bracket. Since I don’t plan to change the solder iron very often, I decided to replace the dovetail with a rectangular tongue-in-groove joint. The pen mount is held in place with M3x10mm button head cap screws threaded into brass inserts mounted in the front bracket.
Gridfinity CNCKitchen Iron Tip holder: The diameter of the openings for the M4 and M5 iron tips have been increased slightly to accommodate the CNC Kitchen tips. The depth of the labels is slightly increased to for better visibility.
Assembly notes: I decided to assemble the version that uses F695 bearings. When I first started to build KB3D kit, it was unclear which STL files needed to be printed. Furthermore, I unfortunately did not recognize the meaning of the abbreviations F695, FHCS and BHCS in the STL file names. After some research I learned that the abbreviation F695 refers to a type of metal bearing, and that FHCS and BHCS describe the head types for the joint screws that can be used in the arm joints. BHCS refers to Button Head Cap Screws and FHCS refers to Flat Head Cap Screws. The KB3D kit uses FHCS, so it’s appropriate to print front, center and rear brackets with file names containing ‘FHCS’ to accommodate the kit’s joint screws. If you print files labeled FHCS, then you do not need to print the files named with BHCS.
Turtlecrawler has provided files for two different joint types. One type uses M5 washers in the articulating surfaces, and the other uses F695 bearings. If you build the variant with washer-based joints, print joint parts with the word ‘washer’ in the STL file names. If you build the variant that uses F695 bearings, print joints and brackets that include ‘F695’ in the STL file names.
M3 Nut Carrier: It was sometimes difficult to use the M3 tnuts included in the kit so I made some 3D-printed nut carriers to hold M3 nuts in the 1515 rails. An STL file for the carrier I drew-up in Autodesk Fusion is included below.
FYI, ‘Build it Basement’ has posted a useful step by step assembly video on YT here.