Saja Boys – Fan-Made K-Pop Light Stick (DIY, USB-C, 18650)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Fan-made light stick designed for personal, non-commercial use, printable in PETG, powered by a 18650 battery with USB-C
- Rating
- 0 / 5
- Likes
- 5
- Downloads
- 19
- Makes
- 0
- Views
- 222
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Costume Accessories
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
🟠 Fan-Made K-Pop Light Stick – DIY Project
This is a fan-made, non-official light stick, designed for personal and non-commercial use.
The model was created because suitable designs were difficult to find, with a focus on simplicity, safety, and ease of assembly.
The enclosure is optimized for PETG, allowing the use of hot glue during assembly without deformation.
The internal design mechanically guides the USB-C charging board and keeps the 18650 Li-ion battery physically separated from the electronics for improved passive safety.
🧩 Key Features
Fan-made DIY light stick
Rechargeable via USB-C
Powered by 1× 18650 Li-ion battery
Simple ON/OFF slide switch
Internal cable routing and component separation
Designed for PETG printing
Assembly using hot glue (no screws required)
🔧 Bill of Materials (BOM)
Battery (18650 Li-ion, 3.7V)
https://a.aliexpress.com/_Evz7YMU
Any quality 18650 battery can be used.
⚠ Many batteries sold online may be clones — use at your own discretion.
Charging Board – TP4056 (with protection, USB-C or Micro-USB)
https://a.aliexpress.com/_EHrGFe4
⚠ Make sure to use a TP4056 with protection circuit (over-charge / over-discharge / short-circuit).
Slide Switch (SS12D00 – 3mm actuator)
https://a.aliexpress.com/_EyjFWlm
LED String (5V, low-power USB fairy lights – red shown)
https://a.aliexpress.com/_EzShYsy
Any low-power 5V LED string can be used.
Other materials
Hook-up wires
Hot glue
Soldering equipment
🖨 Printing Recommendations
Material: PETG (recommended)
Supports: none (or minimal, depending on slicer)
Orientation: standard upright orientation
Infill: 15–25% (as preferred)
Logo transparency note
The first layers of the logo are printed in transparent PETG to improve light diffusion.
Standard PETG can still be used, but transparent filament provides a cleaner and more uniform glow.
⚠ Safety / Disclaimer
This is a fan-made, non-official design shared for personal and non-commercial use only.
This model contains electronics, including a Li-ion 18650 battery.
Basic electronics knowledge is required.
Always use a charging board with protection
Never charge unattended
Do not use damaged batteries
This is not a certified product and not a toy
Intended for adult assembly and supervised use
All rights to the original concept (Saja Boy) belong to their respective owners.
Light Stick K-Pop fan-made – Projet DIY
Il s’agit d’un light stick fan-made, non officiel, conçu pour un usage personnel et non commercial.
Ce modèle a été créé en l’absence de solutions satisfaisantes existantes, avec une attention particulière portée à la simplicité, la sécurité et la facilité d’assemblage.
Le boîtier est optimisé pour une impression en PETG, ce qui permet l’utilisation de colle chaude lors de l’assemblage sans risque de déformation.
La conception interne guide mécaniquement la carte de charge USB-C et maintient la batterie Li-ion 18650 à distance des composants électroniques, améliorant ainsi la sécurité passive.
Caractéristiques principales
Light stick DIY fan-made
Recharge via USB-C
Alimentation par 1 batterie Li-ion 18650
Interrupteur marche/arrêt à glissière
Guidage interne des câbles et séparation des composants
Conçu pour une impression en PETG
Assemblage simple à la colle chaude (sans vis)
Liste du matériel (BOM)
Batterie Li-ion 18650 – 3,7 V
https://a.aliexpress.com/_Evz7YMU
Carte de charge TP4056 (avec protection, USB-C ou micro-USB)
https://a.aliexpress.com/_EHrGFe4
Interrupteur à glissière (SS12D00 – levier 3 mm)
https://a.aliexpress.com/_EyjFWlm
Guirlande LED basse consommation – 5 V (exemple en rouge)
https://a.aliexpress.com/_EzShYsy
Autres éléments
Fils électriques
Colle chaude
Matériel de soudure
Recommandations d’impression
Matériau : PETG (recommandé)
Supports : aucun ou légers selon le trancheur
Orientation : orientation standard
Remplissage : 15 à 25 % selon vos préférences
Note sur la transparence du logo
Les premières couches du logo sont imprimées en PETG transparent afin d’améliorer la diffusion de la lumière.
Un PETG standard peut également être utilisé, mais le filament transparent offre un rendu lumineux plus homogène.
Sécurité / Avertissement
Il s’agit d’un projet fan-made, non officiel, partagé pour un usage personnel et non commercial.
Ce modèle intègre des composants électroniques, dont une batterie Li-ion 18650.
Des connaissances de base en électronique sont nécessaires.
Utiliser uniquement une carte de charge avec protection
Ne jamais laisser charger sans surveillance
Ne pas utiliser de batterie endommagée
Ce modèle n’est pas certifié et n’est pas un jouet
Assemblage par un adulte, utilisation sous supervision
Tous les droits relatifs au concept original (Saja Boy) appartiennent à leurs ayants droit respectifs.