Nubert nuBoxx BF-10 Dolby Atmos Deckenhalter | Ceiling holder
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Für eine Nubert nuBoxx BF-10 benötigt man 4 Stück dieser Halter.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 6
- Makes
- 0
- Views
- 71
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Audio
- License
- Creative Commons — Attribution — Noncommercial
-english version see below-
Die Halterungen sind so dimensioniert, dass noch Platz für ein 2,5 mm² Lautsprechkabel ist und ggf. der Rest davon im Hohlraum zwischen Decke und Lautsprecher untergebracht werden kann. Außerdem sind die Maße der Halterung so gewählt, dass je eine originale Abdeckung von Nubert angebracht ist.
Es empfiehlt sich, die Halterungen so anzubringen, wie auf den Fotos abgebildet. Zwei Halter, die Richtung Wand gerichtet sind, halten den Lautsprecher samt Abdeckung einheitlich parallel zueinander hinten. Zwei Halter an den Seiten, welche vorne angebracht werden, schauen sich gespiegelt zueinander an und halten den Lautsprecher vorne. So ist gewährleistet, dass der Lautsprecher gut gesichert ist und nicht ohne weiteres herausrutschen kann - er ist mechanisch gekontert und kann ausschließlich nur von einer Seite herausgezogen werden.
Empfohlenes Material, Einstellungen und Verbrauch:
PETG
100% Infill
Gewicht je Halter = ~175g
Druckdauer mit 0,20 mm (Structual) für 4 Halter (einen Lautsprecher) = ~ 14h45m
Drucker im 0,28 mm (Draft) = ~ 7h25m
Achtung: PLA (+) wird nicht empfohlen, da dies zu schnell brechen kann!
Montage:
Zwei Bohrlöcher selbst erstellen (oder alternativ Montagekleber) - je nach Untergrund.
Pro Tipp:
Die Auflage und den Rand mit dünnem Filzgleiter ausstattet.
Disclaimer:
Ich hafte nicht für eine unsachgemäße Nutzung oder Montage dieser Halterungen bei Personen-, Sachschäden etc.
++++++++++
The brackets are dimensioned so that there is still space for a 2.5 mm² speaker cable and any excess cable can be stored in the cavity. In addition, the dimensions of the bracket are chosen so that an original cover from Nubert can be attached.
It is recommended to attach the brackets as shown in the photos. Two brackets facing the wall hold the speaker and cover parallel to each other at the rear. Two brackets on the sides, which are attached at the front, face each other in a mirror image and hold the speaker at the front. This ensures that the speaker is securely fastened and cannot easily slip out—it is mechanically locked and can only be pulled out from one side.
Recommended material, settings, and consumption:
PETG
100% infill
Weight per bracket = ~175g
Printing time with 0.20 mm (structural) for 4 brackets (one speaker) = ~ 14h45m
Printer in 0.28 mm (draft) = ~ 7h25m
Caution: PLA (+) is not recommended as it can break too easily!
Assembly:
Drill two holes yourself (or alternatively use mounting adhesive) - depending on the surface.
Pro tip:
Fit the support and the edge with thin felt pads.
Disclaimer:
I am not liable for improper use or assembly of these brackets in the event of personal injury, property damage, etc.