1 / 3
Voron Trident Arctic P12 Slim 120mm Bed Fans with Airflow Guides — image 1
1 / 3

Voron Trident Arctic P12 Slim 120mm Bed Fans with Airflow Guides

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Mount slim 120mm x 15mm fans under your bed with airflow guides for more effective chamber heating

Rating
5 / 5
Likes
22
Downloads
36
Makes
2
Views
602
Reviews
2

Updated at source:

Model information

License
GNU General Public License v3.0

These are bed fan mounts for the Voron Trident designed for the Arctic P12 Slim (non-affiliate link) with no loss of Z travel. The design allows for relatively easy installation and removal of the fans without removing the build plate. Depending on your bed heater, they can dissipate more than 400 watts of heat into your chamber - more than many dedicated chamber heaters.

Other fans with a similar cutout in the corners may work as well, though the P12 Slim in particular seems to cope with the hot environment fairly well despite the operating temperature on the spec sheet. This design will probably also work with 25mm thick fans, but you will lose a small amount of Z travel.

The airflow guides help improve heating of the chamber by directing heated air upwards into the print area (instead of at the panels) and reduce back-flow of heated air. The STLs are for the Trident 300. If you have a larger or smaller Trident, you will likely need to modify the parameters in the CAD model.

Inspired by EEE's 120mm bed fans.

Printing

Heat-resistant material is strongly recommended. This design was tested with PC-ABS and carbon fiber PC blend. ABS and ASA may work as well.

Use standard Voron settings as a starting point. Depending on your material, you may be able to get away with fewer walls and less infill. STLs are provided in the suggested print orientation and should not need supports. For the fan mounts, you may have better bridging results if you set "Bridge counterbore holes" to "Partially bridged" in OrcaSlicer.

BOM

Fan Mounts

  • 6x Voron-spec M3 heat set inserts

  • 6x M3x12 or M3x16 screws

  • 2x M3x20 SHCS

  • 4x M3x8 SHCS

  • 6x M3 t-nuts

Airflow Guides

  • 8-12x M3x6 screws

  • 2x M3x8 screws

  • 10-14x M3 t-nuts

Assembly

  1. Insert M3 heat set inserts into the bottom side of the fan mounts

  2. Attach the fan mounts to the fan using M3x12 or M3x16 screws

  3. Install the fan under the bed using M3 t-nuts, M3x8 SHCS for the outer and rear mounting points, and M3x20 SHCS for the front-inner mounting point

  4. Attach the rear and front airflow guides using M3x6 screws, and the outer airflow guides using M3x8 screws

  5. Wire the fans to the controller board. Make sure you power the fans with 12V, not 24V! See here for pointers if your controller board does not have a dedicated 4-pin PWM fan output - I strongly recommend driving the PWM pin instead of using ground-switched PWM.

Klipper Configuration

Here is the configuration I am using with Kalico. Klipper does not support the reverse option, so you will need to tweak this configuration if you are using mainline Klipper.

[temperature_sensor chamber_rear]
sensor_type: Generic 3950
sensor_pin: PA7

[temperature_fan bed_fans] pin: PA6 max_power: 1.0 shutdown_speed: 0 kick_start_time: 0.5 tachometer_pin: PC2 hardware_pwm: True cycle_time: 0.00004 sensor_type: temperature_combined sensor_list: temperature_sensor chamber_rear combination_method: mean maximum_deviation: 9999

control: pid pid_Kp: 61.470837 pid_Ki: 0.5 pid_Kd: 0 min_temp: -273.15 max_temp: 80 target_temp: 0 max_speed: 1.0 min_speed: 0.0 reverse: True

optional - monitor the tachometer of the second fan if you have it wired separately

[fan_generic bed_fan_2] pin: virtual_pin:bed_fan_2 max_power: 0.01 tachometer_pin: PF3

Tags