Voron Trident Arctic P12 Slim 120mm Bed Fans with Airflow Guides
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Mount slim 120mm x 15mm fans under your bed with airflow guides for more effective chamber heating
- Ocena
- 5 / 5
- Polubienia
- 22
- Pobrania
- 36
- Wydruki
- 2
- Wyświetlenia
- 602
- Oceny
- 2
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Voron Parts & Upgrades
- Licencja
- GNU General Public License v3.0
These are bed fan mounts for the Voron Trident designed for the Arctic P12 Slim (non-affiliate link) with no loss of Z travel. The design allows for relatively easy installation and removal of the fans without removing the build plate. Depending on your bed heater, they can dissipate more than 400 watts of heat into your chamber - more than many dedicated chamber heaters.
Other fans with a similar cutout in the corners may work as well, though the P12 Slim in particular seems to cope with the hot environment fairly well despite the operating temperature on the spec sheet. This design will probably also work with 25mm thick fans, but you will lose a small amount of Z travel.
The airflow guides help improve heating of the chamber by directing heated air upwards into the print area (instead of at the panels) and reduce back-flow of heated air. The STLs are for the Trident 300. If you have a larger or smaller Trident, you will likely need to modify the parameters in the CAD model.
Inspired by EEE's 120mm bed fans.
Printing
Heat-resistant material is strongly recommended. This design was tested with PC-ABS and carbon fiber PC blend. ABS and ASA may work as well.
Use standard Voron settings as a starting point. Depending on your material, you may be able to get away with fewer walls and less infill. STLs are provided in the suggested print orientation and should not need supports. For the fan mounts, you may have better bridging results if you set "Bridge counterbore holes" to "Partially bridged" in OrcaSlicer.
BOM
Fan Mounts
6x Voron-spec M3 heat set inserts
6x M3x12 or M3x16 screws
2x M3x20 SHCS
4x M3x8 SHCS
6x M3 t-nuts
Airflow Guides
8-12x M3x6 screws
2x M3x8 screws
10-14x M3 t-nuts
Assembly
Insert M3 heat set inserts into the bottom side of the fan mounts
Attach the fan mounts to the fan using M3x12 or M3x16 screws
Install the fan under the bed using M3 t-nuts, M3x8 SHCS for the outer and rear mounting points, and M3x20 SHCS for the front-inner mounting point
Attach the rear and front airflow guides using M3x6 screws, and the outer airflow guides using M3x8 screws
Wire the fans to the controller board. Make sure you power the fans with 12V, not 24V! See here for pointers if your controller board does not have a dedicated 4-pin PWM fan output - I strongly recommend driving the PWM pin instead of using ground-switched PWM.
Klipper Configuration
Here is the configuration I am using with Kalico. Klipper does not support the reverse option, so you will need to tweak this configuration if you are using mainline Klipper.
[temperature_sensor chamber_rear]
sensor_type: Generic 3950
sensor_pin: PA7[temperature_fan bed_fans]
pin: PA6
max_power: 1.0
shutdown_speed: 0
kick_start_time: 0.5
tachometer_pin: PC2
hardware_pwm: True
cycle_time: 0.00004
sensor_type: temperature_combined
sensor_list: temperature_sensor chamber_rear
combination_method: mean
maximum_deviation: 9999
control: pid
pid_Kp: 61.470837
pid_Ki: 0.5
pid_Kd: 0
min_temp: -273.15
max_temp: 80
target_temp: 0
max_speed: 1.0
min_speed: 0.0
reverse: True
optional - monitor the tachometer of the second fan if you have it wired separately
[fan_generic bed_fan_2]
pin: virtual_pin:bed_fan_2
max_power: 0.01
tachometer_pin: PF3