1 / 9
The Penultimate Sub250 2s 21700 6" FPV drone, printed frame 35 km flight distance & 55 min of endurance! — image 1
1 / 9

The Penultimate Sub250 2s 21700 6" FPV drone, printed frame 35 km flight distance & 55 min of endurance!

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A semi-printable 11 g in weight 6" frame for sub250 2s 21700 drone that's able to achieve 55 min of flight time.

Rating
0 / 5
Likes
2
Downloads
16
Makes
0
Views
238
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

Mum, look! This battery has a drone!

The goal of this project was simple – take two 21700 Li-Ion batteries and build a drone around it, trying to maximize efficiency. This meant a lightweight frame and large propellers, as the batteries would take up more than half of the 250 g limit.

The frame consists of 8 1x5 mm carbon strips and tiny printed joiners that connect all the parts together. Several iterations were made, focusing on torsional stiffness, as I've tried larger props. The weight grew from 4 g for 3,5" (barebone test frame), to 11 g for 6" (arm braces and some extra bits).

As it turns out, best propulsion combo is achieved with cheap chinese 1503 motors (ones with mesh at the top) and 3" propellers (best hover time), or DJI Mini 3 Pro motors and corresponding 6" propellers (best flight distance). I didn't test more standard FPV motors and T mount props, but I doubt they would perform better.

Such lightweight frame left some spare weight for better light sensitive camera, buzzer and a GPS, with room to spare, so night flying or long range is possible. Finished drone with steel screws weighs ~83 g empty and ~223 g with battery.

Here's my exact setup:

- motors: DJI Mini 3 Pro

- propellers: DJI Mini 3 Pro (6" folding)

- AIO: JHEMCU GHF435AIO V2

- batteries: Reliance INR21700-RS50

- camera: CADDX Ratel Pro

- VTX: HGLRC Zeus Nano VTX 350mW

- antenna: Happymodel 5.8G Crown LDS

- GPS: Walksnail WS-M181 GPS M10

- buzzer: JHEMCU JHE20B Finder Buzzer

My latest flight test resulted in flight time of 55 minutes and distance flown of ~35 km. Battery voltage went from 4,2 V to 2,8 V, and as these cells can be discharged up to 2,5 V, a 1 hour barrier could be broken. Sweet spot for distance is around 40-45 km/h and 15-20° of pitch.

DJI motors bend quite easily, and even 'new' (refurbished from Aliexpress) have some vibrations, so good filters and PIDs are a must. Furthermore, it turns like a bomb truck and slightest propwash can lead to a Rapid Unscheduled Disassembly.

Print in stiffest filament possible, the best is PC-CF. Other things needed are 2 x 5 mm carbon strips found in RC shops (or 1 if no braces are used) and thin CA glue. For assembly, use the provided tool. Make sure to glue all motor mounts flat, as the slightest bend can cause efficiency to drop. To mount AIO, VTX, and camera mount, I've used filament secured with soldering iron to save weight.

In 6" frame, AIO is not straight! It is rotated around vertical axis by 7,6° to the right. Remember to setup firmware of choice accordingly. Magnetometer in GPS is angled at 45° as well. Camera mount holds camera straight!

Check out my other FPV related things for more cool things. Happy printing and safe flying!

Tags