Qidi Q2 Exhaust (HEPA/Activated Carbon Pellets) and 100mm Fan Duct
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This modular exhaust system is meant to enhance the Q2's exhaust/air filtration system.
- Rating
- 0 / 5
- Likes
- 10
- Downloads
- 33
- Makes
- 0
- Views
- 739
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- Open Community License v1
Introduction
This model is meant as a replacement or upgrade of the Q2's exhaust/air filtration system. It allows for the use of cheap replaceable HEPA filters and activated carbon pellets, and fits 100mm exhaust tubes, and a 100mm inline fan.
Use Case
By being able to adjust the HEPA filter, and using easily replaceable activated carbon pellets, this model is meant to improve or replace the Q2's stock filtration system. The components are modular and screw together, and can also adapt to a 100mm exhaust tube. Furthermore the fan duct models can fit a 100mm inline fan, but is for now still a work in progress.
Comments
The inline fan duct is still a work in progress, but the screwing mechanism does work and can also fit a 100mm exhaust tube.
The base on itself contains the HEPA filters (the model fits iRobot Roomba Combo i,e,j Series HEPA filters, but I added the STEP file, so you can adjust it for any HEPA filter that fits the 100mm casing), and the container for the activated carbon pellets (so you can use a bag of AC pellets instead of having to buy new activated carbon filters every time).
For this container, you can adjust the airflow by adjusting the settings to have no top/bottom layers and change the infill percentage (I also added a 3MF for how I printed it as an example).
Fan duct models can fit a 100mm inline fan (the one that has a simple cylindrical shape, not the HVAC systems, yet without the fan ducts you can still use inline HVAC fans as the base model fits 100mm tubes).
There is no hole in the fan duct for the cable, due to different fans having different cable placements, you can simply drill/melt a hole for the preferred cable-outlet.
Printing Instructions
Use a moderate heat-resistant filament, as it needs to withstand the (up to) 65c hot air coming out of the Q2 during/after printing (I used PETG as the HDT is 70/75, but higher resistance would be preferred to be on the safe side)
0.4mm or 0.6mm nozzle preferred, as there are some small details, but 0.8mm might work as well depending on the HEPA filter.
0.2mm layer height (can be varied, same as point above)
Not a structural part, but has to withstand heat, vibrations, and should not wiggle too much, so 20% (Gyroid) infill should be sufficient.
Seam: Random (important for structural integrity) + Scarf (unimportant, just cosmetic)
Arachne Walls
Walls: variable, but I used 5 (as the parts are unsupported, they 'float' in the air, so if only using the base part, I would recommend a higher number to support it's own weight. If using the fan duct as well, a supporting structure is needed, so lower wall count would be good here as well),
Supports:
Base:
For best instant results use the orientation the file comes in. If your printer is well-tuned for long bridging, the (Orca Slicer) 'bridge counterbore holes - sacrificial layer/partial bridging' setting should suffice, but otherwise (tree) supports are needed.
If you have a very-well tuned printer for overhangs, the orientation the slicer recommends, where the scew-side is on the print bed, can be printed without supports at all (which it is designed for), but might rough up the top surface that goes against the printer, needing sanding/a gasket, for a tight seal that doesn't let outside air into the duct. (might add a gasket model later, but I do not use it due to the seal being tight enough for me).
Fan Duct Part one: none needed if your printer can print overhangs well, due to the screwing mechanism being on both sides.
Fan Duct Part Two: No supports needed, but there are some counterbore holes, that could benefit from the 'bridge counterbore holes setting' depending on how well-tuned your printer is for overhangs.
AC Pellet Container: None needed