1 / 2
Montagelehre für Magura Felgenbremsen / Installation gauge for Magura rim brakes — image 1
1 / 2

Montagelehre für Magura Felgenbremsen / Installation gauge for Magura rim brakes

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Lehre zur exakten Montage von Magura Bremsschuhen / Gauge for supporting an exact installation of Magura brake shoes

Rating
0 / 5
Likes
2
Downloads
25
Makes
0
Views
167
Reviews
0

Updated at source:

Model information

Category
Tools
License
Creative Commons — Attribution — Noncommercial — Share Alike

🇩🇪

Beschreibung

Ich hatte immer Probleme die Bremsklötze von Magura Felgenbremsen in allen Dimensionen korrekt auszurichten (vermutlich eine Frage der Übung …)

Mit dieser Lehre ist die Montage ziemlich einfach:

  • Die beiden Schablonen werden auf gegenüberliegende Seiten der Felge geklebt (z. B. mit Tesafilm)

  • Der Steg zwischen den zwei Schablonen hilft bei der tangentialen Ausrichtung

  • Die Schablonen werden nun radial ausgerichtet, sodass sie mittig auf der Felge sitzen

  • Jetzt werden die (neuen) Bremsschuhe so ausgerichtet, dass sie genau auf den Schablonen sitzen

  • Die Bremszylinder auf die Lehre pressen und festziehen (siehe Magura Anleitung)

  • Durch drehen des Laufrads wird die Lehre wieder zugänglich und kann entfernt werden

  • Die Bremsschuhe sollten jetzt

    • genau gegenüber liegen

    • genau 1 mm von der Felge entfernt sein (gegeben, dass das Laufrad gerade läuft)

    • genau mittig zwischen Innen- und Außenkante der Felge sitzen

Druckeinstellungen

Ich habe nur die hier angegebenen Einstellungen getestet, andere funktionieren womögilch genauso gut.

Einstellung

Wert

Anmerkung

Infill

15 %

Eigentlich irrelevant, da das Modell so dünn ist,

dass bei den unten gewählten Werten für massive

Schichten kein Infill erzeugt wird.

Schichtdicke

0,2 mm

Damit die Dicke des Stegs (0,4 mm) und der

Schablonen (1,0 mm) stimmt sollte dieser Wert

so gewählt werden.

Material

PETG

Da der Steg flexibel sein muss würde PLA

vermutlich nicht funktionieren.

Massive Schichten Oben

5

(Standardeinstellung im Prusa Slicer für

Druckprofil 0.2 mm QUALITY)

Massive Schichten Unten

4

(Standardeinstellung im Prusa Slicer für

Druckprofil 0.2 mm QUALITY)

🇬🇧

Description

I always had problems installing the brake shoes of Magura rim brakes s. t. they are not skewed or misaligned in at least one dimension (might be a skill issue …)

With this gauge the installation is pretty easy:

  • Tape the two brake shoe templates on opposing sides of the rim

  • The strip between the two parts helps to align them tangentially

  • Adjust the templates radially to sit exactly in the center of the rim

  • Align the (new) brake shoes with the templates of the gauge

  • Press the brake shoes on the templates and fixate the brake cylinders (see Magura manual)

  • Turn your wheel a bit so you can remove the gauge

  • The brake shoes should now be

    • exacty opposite to eachother

    • exactly 1 mm away from the rim (assuming your wheel is not buckled)

    • exactly center between inner and outer edge of your rim

Print settings

I only tried out the settings below, others might work just as well.

Setting

Value

Comment

Infill

15 %

Actually irrelevant since the model is so thin that

no infill is generated when using the solid layer

values from below.

Layer height

0.2 mm

For the thickness of the strip (0.4 mm) and the

templates (1.0 mm) to be correct, this value

should be used.

Material

PETG

PLA probably would not work since the strip

must be flexible.

Solid top layers

5

(Default setting in Prusa Slicer for printing

profile 0.2 mm QUALITY)

Solid bottom layers

4

(Default setting in Prusa Slicer for printing

profile 0.2 mm QUALITY)

Tags