1 / 2
ID Card Holster with RSA Token and Lanyard Ring — image 1
1 / 2

ID Card Holster with RSA Token and Lanyard Ring

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

ID Card Holster with RSA Token and Lanyard Ring

Rating
0 / 5
Likes
1
Makes
0
Views
84
Reviews
0

Updated at source:

Model information

Category
Office
License
Commercial Use - No Derivative

Overview:

This is a ID card holster that you can use with a lanyard, or belt clip.

Requirements:

  • Your ID card must conform to the standard size (typically the same as a credit or debit card) and be no more than 1mm thick.

  • Your RSA token must be the same model as shown in the image below.

Bill of Materials:

  • PLA Filament colour of your choice

  • 1x 24mm ID split ring (OD must be no more than 27mm)

  • 2x M2 x 12mm Hex socket cap screws (304 or 316 SS)

  • 2x M2 Hex nut (304 or 316 SS)

  • 1x M3 x 8mm Hex socket cap screw (304 or 316 SS)

  • 1x M3 Hex nut (304 or 316 SS)

Tools Needed:

  • Needle nose pliers

  • 2.5mm (M3) hex key

  • 1.5mm (M2) hex key

Assembly:

Printed Parts, ID Card & RSA Token Preparation:
  1. Purchase all items needed (or equivalent alternatives) as per the bill of materials.

  2. Print both parts of the clamshell (front and back) as per the project files or using the included GCode.

  3. Prepare your ID card by removing it from its original holder.

  4. Prepare your RSA token by removing the small split ring  from it.

Clamshell Post Production:
  1. Remove all support material from the screw holes and split ring channel and the cavity for the RSA token.
    The support material from the RSA token cavity can most easily be removed using needle nose pliers to inserts, grip and twist/pull. the supports should come away cleanly. The other support should be able to remove by hand or using either hex key to poke the material out.

Final Assembly:
  1. Take the 2x M2 x 12mm and 1x M3 x 8mm hex socket cap screws and insert them into the front face of the front clamshell half. You may need to screw them in through the plastic. They should sit flush inside the front clamshell half.

  2. Place the front clamshell with the screws in it face down on your work surface so the internal face is facing upwards.

  3. Place the 24mm split ring over the M3 screw protruding from the front clamshell half so that its sits in the circular channel at the top of the ID holster. This is what your lanyard will clip onto.

  4. Place your ID card face down in the recess in the internal side of the front clamshell, it should fit snugly and be flush or slightly recessed inside the recess. The front of the ID card should be visible through the opening in the clamshell, but not be able to fall out.

  5. Take the back half of the clamshell and place it internal face up onto your work surface. Place your RSA token into the cavity so the screen also faces down (so the code can se seen in the window). Place the small split ring you remove into the slot to store it.

  6. carefully pick up the front clamshell half ands place it over the back clamshell half. You may need to manipulate the card slightly the guide bars lock into the place around the card and it sits in its recess cleanly. The two clamshell halves, when combined should have no gap between them.

  7. Pick the entire assembly up carefully so it doesn't come apart and put the M3 nut onto the M3 socket cap screw and tighten it  into its hexagonal recess using the 2.5mm hex key. Do not over tighten it.

  8. Repeat for the two M2 nuts. They sit deeper in the model, so you may need to use a hex key to ensure the lie flat and engage with the thread of each socket cap screw. Do not over tighten.

  9. Take your favorite lanyard and clip it onto the split ring on the top of the holder.

  10. Enjoy.

Result:
  • Your ID badge will be held securely inside the ID holster.

  • Attaching it to your favorite lanyard will allow you to place it over your head and wear it around your neck.

  • When you need to use your RSA token, just flip the holster over and turn it up towards your face. the orientation of the token in holster means the code can be easily read.

Attribution:

  • The lanyard shown in the photos was sourced from a Wellington, New Zealand based Information Security Conference known as Kawaiicon in 2025. They are good people, you should check their website out.

  • I've used a Snapper (stored value public transport card) as the ID card in the photos.

Tags