Radial Spool by Ham Radio Passion (LB8IJ)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Spool to easily manage the radials of your ham radio antenna.
- Rating
- 0 / 5
- Likes
- 10
- Downloads
- 62
- Makes
- 0
- Views
- 379
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Background
In my hunger for more time to operate portable, I'm always on the lookout for new ways to save time. On more than 90% of all my portable operations, I use this Chinese Ground Plane Vertical Antenna. As it is easy to carry, reliable, and quick to set up. Its therefor also my go to antenna for POTA Rovers.
The only little ting slowing me down is to stretch out my radials. The radial supplied with the antenna is easily tangled and messy, and it may take a while to untangle and stretch them out. So I identified this as a point to improve to save me both time and frustration.
My solution is the Ham Radio Passion Radial Spool. A spool that sits mounted to the base of the antenna so all you have to do is put down the antenna, remove the spool clip, pull out the radials and spread them out like you please. all done in a few seconds. And when you are done operating for the day, you may wind back in a matter of seconds.
Bill of Materials
1x Electric Drill Motor brush [Type-A RS550] https://s.click.aliexpress.com/e/_c40vxaYb
1x set of your favorite connector https://s.click.aliexpress.com/e/_c2vzxQKJ
2x 10cm wire [You may use the same as for your radials]
1x Angle bracket [65x65mm] https://s.click.aliexpress.com/e/_c3nWgngJ
2x M3x25mm screw https://s.click.aliexpress.com/e/_c3u4NOsj
1x M3x35mm screw https://s.click.aliexpress.com/e/_c3u4NOsj
4x M3 Nuts https://s.click.aliexpress.com/e/_c3HmywU3
1x 30x6mm Shaft with M4 screw [D6-M4,L30,VCN610-SS]https://s.click.aliexpress.com/e/_c3zQMqdV1x M6 washer [M6x12x1] https://s.click.aliexpress.com/e/_c3MsFdsB
1x M4 washer [M4x9x1]https://s.click.aliexpress.com/e/_c3MsFdsB1x M4 lock nuthttps://s.click.aliexpress.com/e/_c3NNYsXp26awg soft silicone wire for your radials https://s.click.aliexpress.com/e/_c3mA9qdZ
The antenna https://s.click.aliexpress.com/e/_c2uYV1Un
! Notice ! - The 6mm M4 shoulder screw quickly went out of stock after i posted this project and it has proven hard to find a replacement with M4 screw. Howerver a M5 screw should also fit nicely so use a 6x30xM5 sholdered screw as replacement together with a M5 washer and Lock Nut:
1x 6x30xM5 Sholder screw https://s.click.aliexpress.com/e/_c4FJMJn1
1x M5 washer [M5x10x1] https://s.click.aliexpress.com/e/_c3MsFdsB
1x M5 lock nut https://s.click.aliexpress.com/e/_c3NNYsXp
*Note : This post contains AliExpress Affiliate links that support Ham Radio Passion via a small commission from any sales they help generate. It should cost you nothing more.
Tools
Allen Keys https://s.click.aliexpress.com/e/_c4Nm6zgP
Cable Strippers https://s.click.aliexpress.com/e/_opAJSKN
Soldering Iron
Solder
8mm and 10mm HSS drill bits and drill
3D Printer
Assembly
I recommend you watch the video above before you start the assembly.
Prepare the angle bracket
We need to widen one of the outer holes in the bracket to fit the 10mm ground spike.
Use plenty of oil and go slow first with 8mm then widen to 10mm.
Remove any sharp edges with a round file.
Clean the with some alcohol to get all the oils off.
Also remove any oil from the shaft.
Brush preparations
Remove the metal plate holding the bearing of the brush. We are not going to use this.
Bend the two connection points out 90 degrees
Solder the two 10cm wires to each side of the brush
collect both wires and attach the connector.

Put the brush assembly into one half of the spool.
Put the shaft through the first half and guide it through the brush. (In the video I do this in a later step but its easier for you to insert the shaft at this time)
Add the second half of the spool and make sure the orientation is right so the wires can pass through both halves.
Use the two M3x25mm screws and two nuts to lock the pieces together.
Place one M3 nut inside the spool knob using the M3x35mm screw to guide it in place.
Screw the M3x35mm screw through the last hole so that it sticks out on the opposite side of the spool as the shaft does.
Screw the spool knob on to the piece of the 35mm screw sticking out.
On the shaft, add 1 M6 washer, then the L bracket , then the M4 washer, then the M4 locking nut.
Congrats, you are done!
For radial I like to cut 4x5m radial that I add together in a connector that fits the one in your spool.
Then its just to wind it up and head outside.
Good Luck!
And I hope to see you on the bands!
73 de Øystein LB8IJ