1 / 2
Radial Spool by Ham Radio Passion (LB8IJ) — zdjęcie 1
1 / 2

Radial Spool by Ham Radio Passion (LB8IJ)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Spool to easily manage the radials of your ham radio antenna.

Ocena
0 / 5
Polubienia
10
Pobrania
61
Wydruki
0
Wyświetlenia
373
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Background

In my hunger for more time to operate portable, I'm always on the lookout for new ways to save time. On more than 90% of all my portable operations, I use this Chinese Ground Plane Vertical Antenna. As it is easy to carry, reliable, and quick to set up. Its therefor also my go to antenna for POTA Rovers.

The only little ting slowing me down is to stretch out my radials. The radial supplied with the antenna is easily tangled and messy, and it may take a while to untangle and stretch them out. So I identified this as a point to improve to save me both time and frustration.

My solution is the Ham Radio Passion Radial Spool. A spool that sits mounted to the base of the antenna so all you have to do is put down the antenna, remove the spool clip, pull out the radials and spread them out like you please. all done in a few seconds. And when you are done operating for the day, you may wind back in a matter of seconds.

Bill of Materials

! Notice !  - The 6mm M4 shoulder screw quickly went out of stock after i posted this project and it has proven hard to find a replacement with M4 screw. Howerver a M5 screw should also fit nicely so use a 6x30xM5 sholdered screw as replacement together with a M5 washer and Lock Nut:

*Note : This post contains AliExpress Affiliate links that support Ham Radio Passion via a small commission from any sales they help generate. It should cost you nothing more.

Tools

Assembly

I recommend you watch the video above before you start the assembly.

  • Prepare the angle bracket

    • We need to widen one of the outer holes in the bracket to fit the 10mm ground spike.

    • Use plenty of oil and go slow first with 8mm then widen to 10mm.

    • Remove any sharp edges with a round file.

    • Clean the with some alcohol to get all the oils off.

  • Also remove any oil from the shaft.

  • Brush preparations

    • Remove the metal plate holding the bearing of the brush. We are not going to use this.

    • Bend the two connection points out 90 degrees

    • Solder the two 10cm wires to each side of the brush

    • collect both wires and attach the connector.

  • Put the brush assembly into one half of the spool.

  • Put the shaft through the first half and guide it through the brush. (In the video I do this in a later step but its easier for you to insert the shaft at this time)

  • Add the second half of the spool and make sure the orientation is right so the wires can pass through both halves.

  • Use the two M3x25mm screws and two nuts to lock the pieces together.

  • Place one M3 nut inside the spool knob using the M3x35mm screw to guide it in place.

  • Screw the M3x35mm screw through the last hole so that it sticks out on the opposite side of the spool as the shaft does.

  • Screw the spool knob on to the piece of the 35mm screw sticking out.

  • On the shaft, add 1 M6 washer, then the L bracket , then the M4 washer, then the M4 locking nut.

Congrats, you are done!

For radial I like to cut 4x5m radial that I add together in a connector that fits the one in your spool. 

Then its just to wind it up and head outside.

Good Luck!

And I hope to see you on the bands!

73 de Øystein LB8IJ

Tagi