1 / 10
RST99 - 9.9L SFF ITX PC case - 240mm AIO - magnetic panels — image 1
1 / 10

RST99 - 9.9L SFF ITX PC case - 240mm AIO - magnetic panels

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

9.9 liter ITX case for 240mm AIO and 280mm GPUs, with removable magnet-held panels for quick and tool-free access

Rating
5 / 5
Likes
98
Downloads
231
Makes
1
Views
2,868
Reviews
1

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution — Noncommercial — Share Alike

RST99 – 3D Printed SFF ITX PC Case

A compact, fully 3D-printable Small Form Factor (SFF) PC case designed for high-performance hardware in a minimal footprint of just 9.9L.


RST99 compatibility:
  • Mini-ITX motherboard

  • SFX  PSU

  • 240 or 120mm AIO liquid cooler:
    - up to 30mm thickness (27mm recommended)
    - 25mm fan thickness

  • 2.5-slot GPU:
    - length up to  280 mm
    - thickness up to 54mm


Bill of Materials (BOM)

Hardware & Electronics with example links
  • *optional IKEA TERESIA curtain or similar thin fabric (used as a dust filter)


1. Printing

1.1 Recommended printer settings and part orientation

Print all parts in the orientation provided in the STL files unless stated otherwise.

Setting

Recommended

Nozzle

0.4 mm

Layer height

0.2 mm

Wall count

≥4

Top/Bottom layers

≥4

Infill

20–30% (Gyroid or Cubic)

Material

PETG or ABS (CF or GF variant will provide more rigidity for the frame)

Supports

No supports needed

Drying the PETG filament is highly recommended, as cleaning the stringing on the mesh panels can quickly become a major pain.

1.2 Select the parts to print

You have few options depending on the bed size of your printer:

a) 298.7 x 231.2 mm parts fit:

  • Print all normal parts

b) parts up to 235.2 mm long fit:

  • Print all normal parts except mesh_panel_... parts and frame_radiator.
    Use the [split] variants for those parts

c) parts up to 231.2 mm long fit:

  • Print all normal parts except for mesh_panel_... parts, frame_radiator and frame_back_panel.
    Use the [split] variants of those parts

1.3 Print the fitment test part

-HIGHLY RECOMMENDED-
Print the parts to check the magnet fitment without wasting too much filament:

  • tolerance_test_frame_8x3_magnet

  • tolerance_test_mesh_panel_8x2_magnet

The magnets should and sit flush with the surface or sink slightly. They need to fit tightly without applying much pressure and they should not wobble in the slots.

1.4 Print the frame parts

Nothing special here, just print them.
Only thing to mention that obviously 4 legs are needed

Also avoid any air draft as it may cause warping of the big parts, so printing enclosed is strongly advised.

1.5 Print the mesh panel parts

A couple of options here as well:

a) Print the parts as-is without dust filtering - best airflow, but requires periodic cleaning

b) Integrate the dust filtering fabric into the print for all mesh panels except the radiator exhaust.
I found out that IKEA Teresia curtains work really well - they are extremely cheap and perform much better then plastic mesh dust filters while maintaining better airflow.
Procedure:

  1. slice the panel in such a way that you have some sparse infill in the middle

  2. add a pause in the slicer in the middle of the print

  3. add another pause before the next layer

  4. start the print and wait until the first pause

  5. move the printer toolhead out of the way

  6. cut a piece of fabric a bit larger then the mesh panel

  7. fix it by tapping along the perimeter with a soldering iron (at 240°C) to spot weld it to the print
    or use the adhesive tape to fix it to the bed  

  8. set print flow to 75%, speed to 50% and continue the print

  9. wait until the inner perimeters of current layer are finished

  10. pause the print again

  11. carefully cut off the excess fabric with a soldering iron (at 270°C) or with the scissors

  12. continue the print and wait until the layer is finished (the second pause from the slicer)

  13. set the print flow and speed back to 100% and continue the print

You can also edit the G-code so the outer perimeter is printed last at 100% flow and speed for cleaner outer walls. This works well, but G-code editing in the text editor can be tricky.

1.6 Post-Processing

Ideally none is needed. In practice, you will likely want to clean up PETG stringing.


2. Parts Assembly

2.1 Glue the back_plate (optional)

If you printed the [split] version of back_plate, glue or carefully weld the two parts together


2.2 Place the heat inserts and magnets

! IMPORTANT: always check magnet polarity.

When installing magnets, put a few drops of CA glue in the slot and press them in with something flat so they sit flush. You can use CA glue activator spray after placing the magnet to accelerate the process. 

  1. back_plate: 
    - 11x M3x5 heat inserts

  2. frame_corner_bottom and support_MB:
    - 7x M3x5 heat inserts
    - a) for normal mesh panels: 10x 8x3 magnets (blue spots)
      -or-
      b) for [split] mesh panels: 12x 8x3 magnets (yellow spots)

  3. frame_MB:
    - 7x M3x5 heat inserts
    - 4x M3 6mm+6mm standoffs

  4. frame_corners_upper and frame_center_triangle:
    - 4x M3x5 heat inserts
    - 4x 8x3 magnets

  5. bracket_pci_riser:
    - 4x M3x5 heat inserts

  6. frame_top:
    - 3x M3x5 heat inserts
    - 4x 8x3 magnets

  7. frame_radiator (whole or [split]):
    - 8x 8x2 magnets

    - a) for normal mesh panels: 8x 8x3 magnets (blue spots)
      -or-
      b) for [split] mesh panels: 10x 8x3 magnets (yellow spots)

    -7x M3x5 heat inserts

  8. Insert the magnets into the slots on all mesh panels in the same way as for the frame.


3. Building the case

Follow the steps in order. Installing hardware later than recommended can be difficult and may require going back a few steps.

3.1 AIO radiator

Screw the radiator to the frame and place the fans (push configuration from inside)

3.2 Base plate and motherboard mount
  1. Place the C14 socket of the power extension cable to frame_back_plate using two M3x10 screws and M3 nuts

  2. Use three M3x10 screws to attach frame_MB to frame_back_plate

3.3 Bottom corner parts
  1. Add frame_corner_bottom and support_MB and fasten them with 5 M3x10 screws

3.4 Upper corners
  1. Install frame_upper_corners part and secure it with three M3x10 screws

3.5 Center support triangle 
  1. Position frame_center_triangle in place and fasten it with three M3x10 screws

3.6 GPU
  1. Place the bracket_pci_riser and secure it with two M3x10 screws. Upper face should be flush with the top of frame_MB. Small vertical adjustment will be possible afterwards.

  2. Install the bracket_PCIe using two M3x10 screws


  3. Insert the GPU into the PCIe slot of the riser cable and place it like shown below. Gently bend the cable for it to fit. Do not screw the riser PCB to the bracket yet

  4. Fasten the GPU with two M3x6 screws

  5.  Secure the GPU bracket with clamp_gpu and a single M3x10 screw

  6. Now you can fasten the riser cable PCB to the bracket using two M3x10 screws

3.7 Motherboard and AIO
  1. Install AIO pump onto the CPU. If fastening it from the backside of motherboard is not needed, you can do it later in step 5

  2. Insert the EPS (8-pin CPU) power cable now because the AIO pipe will make it much harder after the case is assembled  

  3. Mount the motherboard with four M3x6 screws

  4. Connect the riser cable to the PCIe slot on the MB and carefully bend the cable to shape

  5. Attach the frame_radiator with the installed AIO using four M3x10 screws. If the pump is still not installed onto the CPU, do it now

3.8 PSU
  1. Install the frame_top and fasten it with six M3x10 screws. You can install the power button beforehand as it might be easier then doing this afterwards

  2. connect the cables to the PSU - custom cables are highly recommended due to tight space

  3. put the PSU in place and fasten with four 6-32 UNC screws

  4. connect the other ends of the cables PSU

  5. plug the extension power cable into the C14 socket of the PSU

3.9 Install the legs
  1. Add 4x leg and and fasten them with two M3x10 screws each

3.10 Check the electrical connections
  1. Connect everything that is still disconnected

  2. Plug everything that is still unplugged

  3. Make sure all the cables sit firmly and without gaps

3.11 Put the panels on

Finished!

Your RST99 SFF case is now complete 🎉
Enjoy a compact, powerful, and fully 3D-printed ITX PC.

Tags